Range Rover Parts

Ignition Wiring Harness - the low-tension (LT) link lead within the V8 petrol ignition system. This harness carries the low-tension (primary) side...

rear output shaft LT95 4-speed gearbox V8 - S3 109" Stage 1 V8 - 101" Forward Control - Range Rover Classic 4-speed V8 - Early 110" 4-speed V8

Brake Disc - rear axle, internally vented, for the 5.0L supercharged V8 petrol (AJ133) installation. The disc provides the friction surface that t...

Oil Cooler for the V8 Petrol engine oil cooling system. Reduces engine oil temperature by routing oil through a dedicated cooler core, maintaining...

Rear Brake Pad Kit for the rear axle. This kit supplies a complete axle set of disc brake pads for both rear calipers. The friction pads clamp the...

sensor exhaust gas 2.2L CR DI 16V Diesel OEM Autotec

Gasket cylinder head Grade 3, 3 Hole, 1.22 MM Multi layered steel Reinz

First Speed Bush for the LT77 five-speed manual gearbox. This selective-fit bush supports the first-speed gear on the mainshaft, within the first, ...

Lower Front Suspension Arm Ball Joint - 35 mm The lower ball joint forms the bottom pivot between the front lower suspension arm and the wheel knu...

Drive Belt Tensioner for the auxiliary drive belt on the 2.7L and 3.0L TDV6 diesel engines. The spring-loaded tensioner maintains correct tension ...

Brake Hose Kit - a set of flexible braided brake hoses for the hydraulic braking circuit, carrying fluid from the chassis-mounted hard lines to the...

Injector Refit Kit - Cylinders No.3 and No.4 supplies the parts renewed when a fuel injector is removed and refitted, within the fuel injectors and...

Front Brake Caliper Bracket - left-hand side. Caliper carrier (anchor bracket) in the front brake assembly, bolting to the hub carrier and locating...

Front Brake Caliper Bracket - right-hand side. Caliper carrier (anchor bracket) in the front brake assembly, bolting to the hub carrier and locatin...

CV-Joint GKN

Radiator Assembly for the 4.0L and 4.6L V8 Petrol engine cooling circuit. This radiator assembly is the primary heat exchanger in the engine cooli...

Timing Chain Tensioner - the upper tensioner in the timing chain drive of the 4.4L V8 petrol (BMW M62 B44) engine. It maintains correct tension on...

Rear Brake Pad Set for vehicles built with the size 19 front and rear disc and caliper package, supplied as a complete rear axle set - one kit cove...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

joint washer, various applications, mostly BMW engines. L322 - Oil Pan/Oil Level Indicator M62 B44 4.4 V8 Petrol L322 - Oil Pan/Oil Level Indicato...

Fuel Injector for the 3.5L V8 EFI petrol engine. Meters fuel into the intake port as part of the electronic fuel injection system. For non-catalys...

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.

Intermediate Shaft Circlip Retaining circlip for the intermediate shaft in the LT230 transfer box. Locates on the intermediate shaft to retain the...

Gasket Kit - Front Cover to Block provides the gaskets that seal the front (timing) cover to the cylinder block on the 4.4L M62 V8 petrol engine. ...

Hex Bolt - M10 x 40mm is a metric hexagon head bolt used in the hardware and fixings range for Land Rover vehicles. Thread specification M10, leng...

EGR Valve - 3.0L TDV6 Diesel

Shock Absorber for the front, right-hand side, forming the front suspension damper assembly. Mounted between the body and the front suspension, th...

Valve Guide for the cylinder head of the 2.5L 200 TDi and 300 TDi diesel engines. The valve guide is pressed into the cylinder head and locates th...

Shock Absorber for the rear suspension on vehicles fitted with electronic air suspension, mounting between the chassis and the rear axle. Fits eith...

Throttle body with integrated actuator motor for the 2.2L DW12 common-rail diesel engine. Mounted in the intake tract ahead of the inlet manifold,...

Rear Crankshaft Oil Seal - the main oil seal at the flywheel end of the crankshaft, part of the cylinder block and crankshaft assembly. It seals t...

Head Gasket - V8 - RH seals the right-hand cylinder head to the engine block on the 4.4L AJ-V8 petrol engine. It forms the gas-tight joint between...

Needle Jet for the Solex 175 CD constant-velocity carburettor. The needle jet meters fuel around the tapered jet needle as it rises and falls with ...

Bolt for the TDV6 2.7L and 3.0L diesel engine, used in the engine timing system assembly.

ABS Connector - 4-Way T-Piece for the rear brake hydraulic circuit. This four-port junction connects the rear brake pipes within the ABS braking s...

Alternator Pulley for the 2.5L 300TDi turbo diesel, part of the alternator drive in the engine's charging system. The pulley mounts on the alterna...

Glow Plug threads into the cylinder head and projects into the combustion chamber, heating the intake air on start-up to assist cold-starting on di...

Fuse Box for the vehicle's main electrical power-distribution system. The unit houses the fuses that protect the individual circuits, taking the in...

Front Shock Absorber for the front air suspension assembly, mounting between the chassis turret and the front radius arm alongside the air spring. ...

Bolt. Hexagon-head threaded fastener for general assembly and retaining applications. Supplied individually.

Needle Roller Bearing - LT95

Alternator Bearing Kit - a service kit containing the bearing components required to recondition an alternator unit. Intended for use during alter...

Reverse Idler Gear Assembly for the LT77 five-speed manual gearbox. Provides the reverse gear train, reversing mainshaft rotation for reverse driv...

Shift Plate

Pollen Filter for the cabin ventilation system, installed in the HVAC air intake housing. It traps pollen, dust and airborne particulates from the...

Four-Stage Adjustable Shock Absorber for the suspension damping circuit, mounted between the axle and the chassis mounting point. The damper contr...

Flange Bolt Hex-head flange bolt, M8 x 1.25 x 80mm. General-purpose fastener used in chassis frame and component mountings.

Air to Coil Conversion Kit - 1" Lift, Medium Load replaces the electronically controlled air suspension with conventional coil springs and telescop...