Range Rover Parts

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Air Spring for the front of the electronic air suspension system. The air spring takes the place of a conventional coil spring, using a flexible ru...

Idler Pulley - a smooth-faced guide pulley in the V8 auxiliary (serpentine) drive belt system. Mounted on a fixed pivot, it routes the accessory d...

Expansion Tank Hose - Upper for the Range Rover P38 cooling system. This hose connects the upper port of the coolant expansion tank to the main co...

Anti-Roll Bar Bush is the front mounting bush that locates the anti-roll bar to the chassis. It cradles the bar within its chassis mounting clamp,...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Ignition Lead Set is the set of high-tension (HT) leads in the ignition circuit that carry the spark from the distributor cap to the spark plugs on...

Brake Union Washer is a sealing washer for hydraulic brake line connections. It seals the joint at a brake pipe or flexible hose union, fitting be...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Coolant Hose - Thermostat To Water Pump - V8

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Front Brake Caliper for the right-hand side. The caliper straddles the front brake disc and houses the hydraulic pistons that force the brake pads ...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Air Flow Sensor - V8 is the mass air flow (MAF) sensor for the V8 EFI petrol engine, forming part of the air cleaner and intake assembly. Mounted ...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Breather Adaptor - a threaded fitting in the axle and transfer case ventilation (breather) system. It screws into the axle casing or transfer case...

Alternator generates the vehicle's electrical charge, rated at 12V and 120A. Driven by the accessory belt from the crankshaft pulley, it charges t...

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Bump Stop - rubber suspension bump stop for the Range Rover P38, fitted to limit suspension travel at full compression and absorb the final impact ...

Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...

In-Tank Fuel Pump & Sender Unit for Range Rover P38A petrol applications. This combined assembly houses the electric fuel pump and fuel level s...

Front Brake Caliper Repair Kit for front calipers used with vented discs. The kit supplies the piston seals needed to overhaul the front calipers....

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Drag Link Ball Joint (Short) is a steering linkage joint fitted at the short end of the drag link, within the steering track-rod circuit. It forms...

Radiator Assembly for the Range Rover P38 cooling system, fitted to the 2.5L Diesel engine. The radiator dissipates heat from engine coolant circu...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Brake lever kit

Drive Shaft Oil Seal for the front and rear hub assemblies. This lip seal fits at the inboard end of the front and rear hub carriers, sealing axle...

Mainshaft Taper Roller Bearing supports the mainshaft at the 5th/reverse end of the R380 (and LT77) 5-speed manual gearbox. It carries the mainsha...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Clevis Pin used to secure a clevis or yoke joint in a mechanical linkage. The pin passes through the yoke and mating rod end and is retained by a ...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Camshaft Sprocket for the 4.0L and 4.6L V8 petrol engine, part of the timing drive at the front of the engine. It is driven by the timing chain fr...

COIL IGNITION GEMS (bobineblok RR 4.6 V8) INTERMOTOR

Filler Plug in blue anodised aluminium, replacing the standard cooling system filler and blanking plug at the thermostat housing. Seals against a ...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Mirror Glass - Exterior Door Mirror - Right Hand for the Range Rover P38 exterior mirror assembly. This is the replacement glass insert for the ri...

Bolt Threaded fastener used within the exhaust system assembly.

Brake hose