Range Rover Parts

Upper Rear Tailgate Crossmember is the structural member spanning the top of the tailgate aperture, forming the upper edge of the rear body opening...

Top Coolant Hose for the engine cooling circuit. Carries hot coolant from the engine outlet at the thermostat housing to the top tank of the radia...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Spring Washer, 5/16" - a single-coil split washer fitted under a nut or bolt head to maintain clamp tension. The split coil acts as a spring, exer...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

double washer, restrictor

Spring Washer is an M8 double-coil spring washer used as a fastening component in body and chassis assemblies. The double-coil spring form maintai...

Spring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...

Extended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...

Steering Box Seal Kit reseals the input shaft of the 4-bolt power steering box within the power-assisted steering circuit. The input shaft is wher...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Screw 1/4" UNF x 1" screw used as a fixing in the upper section of the rear tailgate assembly.

Front Brake Caliper is the left-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fro...

Front Brake Caliper is the right-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fr...

Window Motor - LH for the front door electric window regulator system on the Range Rover Classic and Discovery 1. This is the left-hand motor unit...

Brake Master Cylinder of the metric AP type, the hydraulic heart of the braking system. Mounted on the brake servo, the master cylinder converts t...

Spark Plug for the engine ignition system. It threads into the cylinder head so its electrodes sit in the combustion chamber, where the spark ignit...

Fuel Sender Unit is the fuel level sender mounted in a metal fuel tank. A float-operated unit, it varies its electrical resistance with the fuel l...

Temperature switch yellow

Steering Shaft Assembly forming the intermediate link between the steering column and the steering box. The shaft transmits rotation from the stee...

Radius Arm Bush Set - polyurethane bushes for the front radius arm mountings at the axle end of the arm, supplied as a set of four in black. The b...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Radius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...

Lower Strut Gaiter for the rear self-levelling suspension unit. This flexible rubber boot fits over the lower ball joint of the self-levelling str...

Exhaust U-Bolt - a U-bolt clamp used to secure a joint in the exhaust system. It retains the exhaust front pipe (downpipe) connection, clamping th...

Front Shock Absorber Turrets: the tubular mounting towers that locate the upper end of the front dampers. Each turret bolts to the chassis and pro...

Saddle Clip for the power steering hydraulic circuit. This saddle-shaped clip clamps a power steering pipe or hose to its mounting point, retaining...

Tank Mounting Spacer - a spacer used in the fuel tank mounting assembly. It sets the correct standoff between the tank and its supporting bracketr...

Hex Nut is a metric M5 hexagonal nut used as a general-purpose threaded fastener across multiple vehicle assemblies. It runs onto a matching M5 ma...

Glazing Seal - the glazing rubber that lines the front door window channel and cushions the glass within it. It grips the edge of the glass, holds ...

Brake Pipe Union is a male threaded fitting used in the brake hydraulic pipework. It belongs to the brake pipe and fitting group. The union nut th...

Polyurethane Rear Upper A-frame suspension link bush set (NTC1773), chassis end.

Brake Disc Mud Shield - Front, LH, mounted behind the left-hand front brake disc. The shield sits between the stub axle / hub and the brake disc, ...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Gasket - Transfer Box Gearchange Housing Plate

O-Ring - Gear Change Selector seals the gear change selector shaft where it enters the transmission housing, preventing lubricant leakage at the sh...

Timing Belt - toothed camshaft drive belt for the 200 TDi engine. Synchronises the crankshaft with the camshaft and injection pump, holding valve ...

Spark Plug for the petrol engine ignition system, fitted to the 2.5L four-cylinder and 3.5L/3.9L V8 petrol engines. It screws into the cylinder he...

Heater Hose for the 200 TDi engine, forming part of the coolant circuit that supplies the heater matrix. Routes engine coolant to the heater core,...

Viscous Coupling - the temperature-controlled fan drive that turns the engine cooling fan on the 2.5 litre 300 TDi diesel. The coupling sits betwe...

Timing Belt for the camshaft drive of the 300 TDi diesel engine, running within the timing belt and tensioner assembly at the front of the engine. ...

Parking Brake Switch mounts on the handbrake lever assembly and operates the handbrake warning lamp in the instrument cluster. When the parking br...

Double Cardan Front Propshaft Kit - a heavy-duty front propshaft for the LT230 transfer box, using a double cardan (constant-velocity) joint at the...

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Alternator assembly within the engine charging system, installed on the front-end accessory drive and driven by the auxiliary belt to convert mecha...

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...