Range Rover Parts

Heavy Duty spring Range Rover rear +0mm

Track Rod Clamp Kit secures the track rod within the steering linkage assembly, holding the joint in position so the steering geometry stays set. ...

The cable forms the mechanical link between the handbrake operating lever and the handbrake mechanism within the handbrake assembly, transmitting l...

Steering Damper - Heavy Duty Type for the steering linkage assembly on Discovery 1 and Range Rover Classic. This hydraulic damper is mounted betwe...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Warning Bulb Switch (Red) for the facia auxiliary switch panel. Mounted in the upper facia switch bank, this illuminated switch carries an integra...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Head Gasket Set - V8

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Speedometer Angle Drive is a right-angle gear adapter fitted in the speedometer drive line, configured for the right-hand (RH) routing. It takes t...

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

Body Mounting Kit renews the body-to-chassis mounting points, where the body is located and secured to the chassis frame. The rubber mounts isolat...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Decoke Gasket Set for the 3.9/4.0/4.2L Rover V8 EFI petrol engine. This is the set of gaskets and seals used to reseal the top end of the engine - ...

Steering Column Lock - the steering column lock and ignition switch assembly. Mounted on the steering column, it mechanically locks the column whe...

Reverse lamp switch LT85 V8

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Anti-Roll Bar Bush in the suspension anti-roll bar mounting, locating the stabiliser bar against the chassis. It cradles the anti-roll bar at its ...

Radiator Hose - Bottom - V8 Petrol

Bottle sensor

Modular Steel Wheel - Black - 7J x 16 A modular steel road wheel finished in black, sized 7J x 16 with an ET08 offset. The steel construction suit...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Dislocation Cone - Rear Coil Spring for the rear coil spring seat assembly. When long-travel shock absorbers or lowered top-mount shock relocators...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Drive Belt is the poly-vee auxiliary drive belt for the 2.5L 200 TDi diesel engine. Driven from the crankshaft pulley, it transmits power to the p...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Return to Centre Steering Damper for installation within the steering linkage assembly. This unit mounts between the axle steering arms and the st...

Rear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...

Front suspension shock absorber designed to control spring oscillation and maintain tyre contact with the road surface. Twin-tube low-pressure ni...

Rocker Cover Gasket Set for the 2.5L VM turbo diesel engine, sealing the rocker cover to the cylinder head. The gasket seats between the rocker co...

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Bolt is a general-purpose imperial-thread fixing with a 5/16-inch UNC (Unified Coarse) thread and a 7/8-inch length. Used as a common fastener acr...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Window Motor for the right-hand front door, part of the electric window regulator assembly. It drives the regulator mechanism to raise and lower th...

Window regulator front RH

Brake Master Cylinder - RRC

Hub Oil Seal for the front axle, sealing the front hub and drive shaft assembly to retain hub lubricant and exclude water, dirt and grit from the w...

Power steering seal kit

Carburettor Gasket Kit for the Zenith/Stromberg 175CD carburettor fitted to the 3.5L V8 petrol engine. The kit supplies the gaskets and seals need...