Range Rover Parts

Decoke Gasket Set for the 3.5L V8 petrol engine with fuel injection (EFI). The set supplies the gaskets and seals needed when the cylinder heads a...

Kit - 7 Inch Headlamp Fixing - Series - Defender

Servo unit RRcl D1

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Hex-Head Setscrew, M6 x 20 mm, metric thread, fully threaded to the head. A general-purpose fixing used to secure components at M6 mounting points.

Bolt 3/8" x 2"

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Thermostat regulates coolant flow within the engine cooling circuit of the 2.5L 4-cylinder VM Turbo Diesel. Housed in the thermostat housing at th...

Bumper End Capping, front left-hand - the end finisher fitted to the outer end of the front bumper. It closes off the open end of the bumper, givi...

Alternator of the Lucas A133 type, rated at 85A, for V8 EFI petrol engines. Driven by the auxiliary belt from the crankshaft as part of the engine...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Front Wiper Motor for the windscreen wiper assembly. The motor drives the wiper linkage and wheelboxes that sweep the front wiper blades across the...

Power Steering Hose - Box to Reservoir is a hydraulic hose in the power steering return circuit. This hose carries hydraulic fluid from the steeri...

Auxiliary Lamps - Spoiler for the Range Rover Classic, mounted in the front spoiler. This pair of 55W auxiliary lamps supplements the main headligh...

Fuel Pump is a low-pressure in-tank unit forming part of the fuel delivery system on petrol applications. Mounted inside the fuel tank, it acts as...

Philidas Nut is a 5/16" UNF all-metal self-locking nut. A deformed collar gives it prevailing-torque resistance to loosening under vibration, and i...

Drop Arm - LHD - D1/RRC

Bottom Radiator Hose - the lower coolant hose in the engine cooling circuit, connecting the radiator outlet to the water pump inlet. It returns co...

Radius Arm Bush - Front - mounts the front radius arm at its axle end within the front suspension. The radius arm locates the front axle longitudi...

Handbrake Cable transmits lever movement to the transmission handbrake, the drum brake mounted on the transfer box rear output. The outer sheath i...

Bump Stop limits suspension travel within the suspension assembly, cushioning the contact between the axle and chassis at the extremes of wheel mov...

Front Bumper in a black finish, forming the front impact member bolted to the front chassis crossmember. Incorporates the provision for the headla...

Left-Hand Rear Bumper Bracket that secures the rear bumper assembly to the body structure on the Range Rover Classic. This bracket is for the left...

Right-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the right cylinder bank exhaust manifold outle...

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

Radius Arm Bush Set - Polyurethane fits at the axle end of the front radius arms, within the front suspension radius arm and axle location assembly...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Centre Exhaust Silencer sits in the middle section of the exhaust system, reducing exhaust noise as gases pass from the front pipe rearward toward ...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Axle Breather Pipe Clip from the axle breather system, retaining the breather hose along its run from the axle case up to its higher mounting point...

Exhaust Bracket for the exhaust mounting system. This bracket supports the exhaust line at the section immediately behind the front silencer, loca...

Fuel Tank Drain Plug - the threaded plug that seals the drain point at the base of the fuel tank. Removing it allows the tank to be drained for se...

Front Coil Spring is a front road suspension coil spring for V8 petrol, left-hand-drive applications. It supports the front of the vehicle and set...

Exhaust Downpipe - V8 - RH - RRC

Steering lock

Exhaust Mounting supports the rear section of the exhaust system, suspending it from the underbody. This rubber mounting locates the rear of the t...

clamp exhaust pipe RRclassic (with twin exhaust pipes)

Windscreen Seal is a rubber glazing seal fitted around the windscreen aperture. It retains the windscreen glass in the body aperture and seals the...

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...

Heater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...

Exterior Door Handle Seal for the door locks and handles assembly. The seal sits between the outer door handle and the door skin, closing the gap ...

Rivet is a body fixing used to secure sheet-metal panels, wheelarch liners and trim to the vehicle structure. It forms a permanent, vibration-resi...

Torx Countersunk Screw is a fixing used within the upper tailgate assembly. The countersunk head seats flush with the mounting surface, while the ...

Bonnet Striker is part of the bonnet latch mechanism — the striker that the bonnet catch engages to hold the bonnet closed. When the bonnet is shu...

Window Regulator operates the manual front door glass on the right-hand side, forming part of the door window lift assembly. Mounted inside the do...

Window Regulator for the left-hand front door, operating the manual window lift mechanism. The regulator converts the rotation of the winder handl...

Trim Pad Clip is a fastening clip used to secure interior trim pads to the bodyside and door structure. It locates into a pre-formed hole in the p...