Range Rover Parts

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Front Door Hinge mounts the front door to the body pillar, carrying the door's weight while allowing it to pivot open and closed. The hinge locate...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Driving Member Bolt secures the driving member, or drive flange, to the wheel hub. The driving member transmits drive from the axle halfshaft to t...

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Ballast Resistor Resistor in the ignition primary circuit of the 3.5L V8 petrol engine. Wired in series with the ignition coil, it drops the suppl...

Rocker Cover O-Ring for the VM four-cylinder turbo diesel engine, sealing the rocker (cam) cover to the cylinder head. It maintains the oil-tight ...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

O-Ring for the fluid suction pipe of the ZF four-speed automatic transmission. Seals the joint at the suction (pick-up) pipe that draws automatic ...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...

Shaft coupling

Brake Union Washer is a sealing washer for hydraulic brake line connections. It seals the joint at a brake pipe or flexible hose union, fitting be...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Cable Tie, Panel Fixing: grey cable tie strap with a panel fixing, 4.6 x 165 mm.

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Fuse - 10A for Land Rover electrical systems. This 10A fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Throttle Potentiometer Gasket seals the throttle position sensor (throttle potentiometer) to the throttle body on the V8 EFI system. It forms the ...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Cable Tie, a push-fit strap for routing and securing wiring and hoses. The tie strap bundles and secures wiring looms, pipes and hoses, locating i...

Head Gasket for the Land Rover 300TDi 2.5L 4-Cylinder Turbo Diesel engine, fitted at the cylinder head-to-block joint. This is a multi-layer steel...

Gasket inspection cover

Bush

Starter Motor Solenoid is the electromagnetic switch mounted on the starter motor body, forming the switching element of the engine starting circui...

Bolt is a hexagonal-head fastener from the engine and transmission mounting hardware. It secures the engine and gearbox mounting brackets and thei...

Shock Absorber Bush Set for the upper damper mounting, polyurethane. The bushes sit in the upper damper mounting, isolating the damper from its mo...

Rear Axle Breather Pipe vents the rear axle casing. It equalises internal air pressure as the axle heats and cools, allowing the casing to breathe...