Range Rover Parts

Swivel Pin Housing Shim - 0.005in is a 0.005 in (0.13 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Swivel Pin Housing Shim (0.003in) used to set the swivel pin bearing preload on the front axle swivel assembly. The shim is fitted at the swivel p...

Sleeve hub RRC (generic picture, not the actual part).

Spring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...

Oil Seal for the LT95 four-speed gearbox, retaining lubricant within the gearbox and transfer casing. It runs against a rotating shaft to keep gea...

Gasket gearbox front cover and oil pump. LT95 4-speed gearbox - Early 110 V8, - S3 109" stage 1 V8, - 101" F.C. - Early Range Rover Classic

Flywheel Ring Gear (starter ring gear) for the diesel flywheel, part of the clutch and flywheel assembly. The toothed ring is fitted around the fl...

Differential Shim - 0.060in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Differential Shim - 0.048in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Shim, 0.040in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Mudflap Bracket - Front - LH secures the front mudflap to the body on the left-hand side of the vehicle. Part of the front mudflap assembly, the b...

Mudflap Bracket for the front, right-hand side. This bracket secures the front mudflap to the body, holding it at the correct position behind the ...

Wing Seal A rubber sealing strip fitted to the inner wing. It seals the joint at the wheelarch and valance to keep out water and road debris.

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Front Wing Mounting Rail for the left-hand side. This rail forms the upper mounting line for the front wing, providing the fixing points along whi...

Front Wing Mounting Rail for the right-hand side. This rail forms the upper mounting line for the front wing, providing the fixing points along wh...

Crown Wheel Bolt with British Standard Fine (BSF) thread, used to secure the crown wheel to the differential carrier in early Land Rover axles. Tw...

Mudguard - Power Take Off for the centre power take-off (PTO) housing. Mounted to shield the centre PTO unit from mud, water and road debris. Prot...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Pipe Clip used to secure and route pipework such as fuel breather and roll-over anti-spill lines. The clip holds the pipe at a fixed point to prev...

Glass Door - LH

Halogen Bulb - H4 100/80W (Non-CE). Dual-filament headlight bulb rated 100W high beam and 80W low beam, providing increased light output over the s...

rock slider, rock guards (pair) BA 2091 Generic picture, the set supplied is BLACK coated, NOT galvanised.

Fuel Catch Tank Pipe - part of the V8 petrol evaporative loss (fuel vapour) system. This pipe connects to the fuel catch tank, carrying evaporativ...

Wheel Chock for securing a stationary vehicle. Placed against a tyre, the wedge-shaped chock prevents the vehicle from rolling when parked on an i...

strap MTC8527

bracket 390384

Dash Assembly Bracket - a structural support bracket forming part of the dashboard (fascia) assembly. The bracket provides a fixing point within t...

Rear Mudflap Bracket for the Range Rover Classic body. This bracket mounts to the rear bodywork to carry the rear mudflap, positioning it correctl...

Locking Wheel Nut Set - a set of four keyed security nuts, one per wheel, fitted in place of a standard wheel nut to deter theft of the road wheels...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

Automatic Transmission Sump Plug - Magnetic for the automatic gearbox valve block. This drain plug fits the automatic transmission sump and incorp...

Retaining Clip used in the parking brake (handbrake) assembly and the automatic transmission gear-change linkage. The clip secures a pivot pin or ...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Bulb & Holder - Green, an illumination bulb supplied in its colour-coded green holder for the dashboard and switch panel lighting circuits. Th...

Valve Block Kit Repair

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

SRS ECU - the Supplemental Restraint System electronic control unit, commonly known as the air bag control module. It sits at the centre of the SR...

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Actuator