Range Rover Parts

Output Shaft Seal for the extension housing of the ZF 4-speed automatic gearbox. The seal fits at the rear of the gearbox, where the output shaft ...

Front Anti-Roll Bar Bolt secures the front anti-roll bar within the front suspension assembly. It fixes the bar to its mounting, holding it in pos...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Spring Retainer secures the upper outer mounting of the rear coil spring and damper within the rear suspension assembly. It clamps the top of the ...

Castle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...

Oil Separator Drain Hose for the 300 Tdi 2.5L 4-cylinder turbo diesel engine, part of the crankcase ventilation system. It returns the oil collect...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Swivel Ball Inner Bearing Housing for the front axle swivel assembly. It locates and supports the inner bearing within the swivel ball, maintaining...

Timing Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Headlamp Assembly for the front exterior lighting system, supplied as a pair. Each crystal-style halogen unit mounts in the front lighting housing...

Link Clip - an anti-rattle clip for the side door latch linkage. It retains the latch operating rod within the door lock mechanism, holding the li...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Power Steering Reservoir

Coolant Temperature Sensor threads into the engine coolant circuit and reports coolant temperature to the instrument and engine management systems....

Clutch Master Cylinder - 200TDi, VM & V8

Taper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Shock Absorber Bush - Polyurethane is a polyurethane mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chas...

Injector Bolt secures the fuel injector clamp within the cylinder head on the 2.7 and 3.0 V6 diesel engines. The M6 x 35 mm bolt retains the clamp...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

screw M5 x 12

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Door Lock Control Cable is the front-door cable that links the lock mechanism to the door latch, transmitting the locking and unlocking action thro...

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...

sensor lambda, Sensor-oxygen multi point injection

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Bolt - a hexagonal-head bolt with a 3/8" UNF (Unified Fine) imperial thread and a 1" length. Used as a suspension and chassis fixing at points such...

Clutch Release Fork - Heavy-Duty is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch sl...

Coolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...

Crankshaft Oil Seal seals the front timing cover where the crankshaft nose passes through it. Fitted to the 2.5L 300 TDi diesel engine, the seal r...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Lower Steering Column Universal Joint for the steering column assembly. This universal joint sits at the lower end of the steering shaft, transmitt...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Lokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...

Timing Belt Kit for the camshaft drive of the 2.5L 300 Tdi turbo-diesel engine. The timing belt synchronises crankshaft and camshaft rotation to m...

Headlamp Body with manual headlamp levelling. The headlamp body is the housing and reflector unit that carries the headlamp light unit and mounts ...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Fuel Filter Housing Assembly for the fuel delivery line on carburettor petrol engines, including the 3.5L V8. This assembly mounts in-line between...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...