Range Rover Parts

Power Steering Pump Pulley mounts on the power steering pump within the engine's auxiliary drive on the 2.5L 300TDi turbo diesel. Driven by the au...

Fuel Spill Pipe forms part of the fuel injection system on the 2.5L 200TDi turbo diesel engine. It links the injector leak-off unions, collecting ...

EGR Pipe Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine. This rubber hose forms part of the exhaust gas recirculation (EGR) circuit, conn...

Camshaft operates the valvetrain of the 2.5L 300TDi diesel engine. Its lobes actuate the pushrods to open and close the inlet and exhaust valves.

Fuel Injector for the 2.5L 300TDi 4-cylinder turbo diesel engine. This direct injection fuel injector delivers metered, atomised fuel into the pre...

Connecting Rod Bush is the small-end bearing bush pressed into the little-end of the connecting rod. It forms the bearing surface for the gudgeon ...

Connecting Rod Assembly for the 300TDi 2.5L turbo diesel engine. The connecting rod links a piston to the crankshaft, transmitting the force of co...

Front Crankshaft Oil Seal seals the front of the crankshaft where it passes through the timing cover. It prevents oil loss at the crankshaft pulle...

Flywheel Housing Gasket for the 200 TDi diesel engine, sealing the joint between the flywheel (or drive plate) housing and the rear face of the cra...

Cylinder Head Pair for the Rover V8 EFI petrol engine - the two aluminium-alloy heads that close the top of the left and right cylinder banks. Eac...

Rocker Arm operates on the rocker shaft in the 200TDi diesel valvetrain. Driven by the pushrod, it transfers camshaft motion to actuate the valve.

Exhaust Valve for the cylinder head valvetrain of the 200TDi and 300TDi 2.5L turbo diesel engines. It seats in the cylinder head exhaust port and ...

Relief Valve Spring is the coil spring that controls the opening pressure of the oil pressure relief valve in the 300Tdi engine lubrication system....

Inlet Valve seats in the cylinder head of the 3.5L and 3.9L V8 petrol engine. It controls the intake charge entering the combustion chamber on twi...

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

Injector O-Ring is a sealing ring fitted to a fuel injector in the V8 EFI (electronic fuel injection) system. It seals the injector against its mo...

Rear Spring Spacer Kit for the coil-spring rear suspension, supplied as a pair of blocks that fit between the axle and the spring seats to raise ri...

Limited-Slip Differential is a helical-gear (Detroit TrueTrac type) limited-slip differential centre for the rear axle, with a 10-spline output. T...

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Winch Bumper Fitting Kit - the mounting hardware set for installing the DA5621 steel winch bumper. Supplies the fixings needed to attach the bumpe...

Rear Radius Arm locates the axle and controls its fore-and-aft movement, with geometry set for a 2 inch suspension lift. The revised arm restores ...

Air Filter - air filter for the 3.5 V8 carburettor engine, fitted at the carburettor intake to filter incoming air before it is drawn through the c...

Cold Air Intake Filter replaces the complete air filter box in the induction system with an exposed reusable filter, drawing cooler air to the engi...

Carburettor Conversion Kit - replaces the twin Stromberg or SU carburettor setup on the Rover V8 with a single four-barrel carburettor mounted on a...

Workshop Manual - a Haynes service and repair manual covering routine maintenance, servicing and overhaul procedures for the V8 petrol engine (3.5 ...

Waterproof Seat Cover Set for the rear seats, tailored to the split rear bench. The set contains a cover for the two-seat section (back and base),...

Brake Hose Kit is a set of flexible hydraulic brake hoses for the front and rear braking circuits, supplied at +40mm over standard length to suit r...

Differential Pan Cover - weld-in replacement cover for the axle differential housing, incorporating a filler/level plug. The cover welds onto the ...

Harness Edge Clip that routes and secures the wiring harness within the facia and centre console area. The clip attaches to a panel edge and retai...

Mirror Assembly - complete right-hand exterior door mirror assembly with electric adjustment. The mirror head and mounting base form a single asse...

Wing Plastic Brake 1144r

Shock Absorber A hydraulic telescopic shock absorber (damper) for the rear suspension. It damps spring oscillation to control body movement and ke...

Shock absorber rear Pro-Comp gas 0-25 mm (+1")

Shock Absorber - front gas-charged suspension damper. Mounted between the front axle and the chassis, it damps spring oscillation to control body ...

Jack Rack. A mounting rack that stows and secures a jack to the vehicle, holding it firmly in place for transport.

Service Kit - 3.5L V8 for routine servicing of the 3.5 litre V8 carburettor petrol engine. This kit contains the consumable parts for a full servi...

Bolt Hex-head fastener, M10 x 100mm, used as a chassis and crossmember fixing. Commonly fitted to secure the gearbox crossmember, and used across ...

Bolt, M10 x 45 mm, securing a mounting bracket to the chassis. A threaded fastener with a 10 mm metric thread and a 45 mm shank length. It forms t...

set screw M6 x 25mm 8.8 various applications

Shock Absorber Boots are protective covers that fit over the shock absorber body to shield the shaft and seal from mud, grit and debris. Supplied ...

Haynes Range Rover Classic repair manual

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Front Twin Shock Tower (Pair) - an uprated front shock absorber mounting set for coil-sprung suspension that allows a second shock absorber to be f...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...