Range Rover Sport L320 Parts

Suspension Arm - front lower control arm (wishbone) for the right-hand side, fitted to models with air suspension. It connects the chassis to the l...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Spindle rod link

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Rear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Crankcase Breather Valve for the crankcase ventilation system of the 4.4L V8 petrol and 4.2L supercharged V8 petrol engines. It regulates the flow ...

Brake Disc Bolt - M10 x 20mm securing the brake disc to the hub flange. M10 x 20mm bolt with 1.5mm thread pitch. Multiple bolts are required per d...

Brake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...

Brake Disc - a rear vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw a...

Circlip for the lower steering knuckle bush. This circlip retains the bush within the lower steering knuckle, forming part of the front axle and s...

Bolt Mounting bolt for the front suspension arm. Part of the front suspension assembly, it secures a front upper or lower control arm (wishbone) a...

Pollen Filter for the cabin ventilation system, installed in the HVAC air intake housing. It traps pollen, dust and airborne particulates from the...

Fuel Tank Strap for Discovery 3, Discovery 4, and Range Rover Sport equipped with the 10MY-specification fuel tank (two vent pipes). This strap se...

Rear Lower Suspension Arm (Right-Hand) is a lower control arm in the rear independent suspension. It locates the rear hub carrier to the chassis s...

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Air Filter - the air cleaner element for the engine air intake system. The element sits within the air cleaner housing and filters incoming air be...

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Exhaust Gasket - downpipe joint gasket sealing the connection between the exhaust downpipe and the intermediate pipe section. Fits across several ...

Gearbox Sump Gasket for the automatic transmission oil pan. This is the gasket only - it seals the oil pan and oil screen to the gearbox case. For...

Front Lower Suspension Arm, right-hand side, for vehicles equipped with Roll Stability Control (RSC). Part of the independent front suspension ass...

Modular Steel Wheel is a heavy-duty 8-hole steel road wheel finished in satin black. Specification: 18 x 8 inch, ET45 offset, 5 x 120 PCD, rated t...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Adjustable Tow Bar Kit with quick-disconnect coupling for the rear towing system. The height-adjustable drop plate lets the tow ball height be set...

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Front Propshaft, connecting the transfer case front output flange to the front axle differential input pinion. The propshaft transmits torque to t...

CV boot gaiter kit D3, D4, RRsp

Lower Rear Knuckle Suspension Bush for the rear suspension. This bush fits the lower mounting of the rear knuckle (wheel carrier), forming the comp...

Compressor assy 9A (compressor only)

Special bolt

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Parking Brake Actuator Repair Gears - replacement drive gears for the electric parking brake (EPB) actuator module. Replaces the internal gears th...

The OEM Service Kit is designed for Discovery 3 (4.4 V8 EFI Petrol) and Range Rover Sport (4.2/4.4 V8 Petrol) models. This kit includes all the ess...

Fitment: All Models 2.7 TDV6 To (V) 6A999999 2.7L TDV6 diesel models to (VIN) 6A999999

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Brake hose

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...