Range Rover Sport L320 Parts

24v dsl long belt

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Door Handle Cap - LH is the left-hand end cap for the exterior front door handle assembly, incorporating the lock barrel aperture. The cap forms t...

Timing Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Fuel Filter within the diesel fuel supply assembly. This filter traps particulate contamination in the fuel supply circuit before fuel reaches the...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Front Differential Bush Mounting bush that locates and supports the front differential within the axle case. The bush isolates the differential fr...

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

EGR Thermostat Assembly that regulates coolant flow through the exhaust gas recirculation (EGR) cooler on the 2.7-litre V6 and 3.6-litre V8 diesel ...

Oil Pump for the 2.7L and 3.0L V6 diesel (Lion) engine, operating within the lubrication circuit as part of the oil pump and sump assembly. Driven...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Cigar Lighter Ring - Illuminated

Height Sensor Jumper Lead for the electronic air suspension system. This connecting lead links a ride-height sensor to the chassis wiring harness,...

Gear Selector Linkage Bush in the floor gear-change assembly of the ZF 6HP26 / 6HP28 6-speed automatic transmission. The bush forms the pivot at t...

Rear Output Shaft Oil Seal for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It seals the point where the output shaft leaves the rear ...

Spring Washer used in the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It is fitted under the fastener securing th...

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Bolt for the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It secures the gear change mechanism to its mounting on ...

Asy Lamp

Flanged Nut, M8. The integral flange spreads clamp load across the joint face and removes the need for a separate washer. Used in the exhaust syst...

Grommet for the inspection aperture in the rear brake backplate. The backplate carries an access hole through which the parking brake shoe adjuster...

Adjusting Nut is an M17 flanged nut used in the rear suspension toe link assembly. It locks the toe link adjuster at its connection to the rear kn...

Rear Brake Pad Set for the rear disc brake assembly, supplied as an axle set covering both rear wheels. The pads sit in the rear caliper carrier a...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

Radius Arm Bush for the front radius arm, upper position. It press-fits into the arm and forms its pivot at the mounting. Part of the front radius...

Oil Filter is the engine oil filtration element within the lubrication system, removing wear particles and contaminants from the oil before it circ...

Air Bleed Valve is fitted to the engine cooling system to release air trapped in the coolant circuit. Opened during filling and bleeding, the valv...

Fuel Injector Seal - Upper - sealing ring for the upper position on the fuel injector, part of the fuel injectors and pipes group on the V8 petrol ...