Range Rover Sport L320 Parts

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Locking Flange Nut - M8 for fastening applications requiring vibration-resistant fixings. A prevailing-torque hexagonal nut with an integral flang...

Injector Bolt secures the fuel injector clamp within the cylinder head on the 2.7 and 3.0 V6 diesel engines. The M6 x 35 mm bolt retains the clamp...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Wheel Nut - Black secures a road wheel to the hub, clamping the wheel against the hub face when tightened to the specified torque. The nut carries...

Left-hand inlet manifold for the 3.0L V6 diesel engine induction system. The manifold distributes intake air from the charge air system into the ...

Throttle Housing Seal for the 2.7L TDV6 and 3.0L SDV6 diesel engines, sealing the throttle body to the air intake. The seal sits between the throt...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Fuel return tube O-ring seal

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Right-hand inlet manifold forming part of the air intake system, distributing charge air from the throttle and intake ducting evenly to the cylinde...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

o-ring oil cooler 3,0 TDV6

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Camshaft Position Sensor within the engine management system of the 3.0L diesel engine. This sensor monitors camshaft rotational position and tran...

Accessory Drive Idler Pulley

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Transmission Oil Pan & Filter Kit - the lower fluid pan for the ZF 8HP70 8-speed automatic transmission, incorporating an integrated fluid filt...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Service PCV Kit

Timing Chain Guide for the primary timing chain, fitted on the right-hand side of the timing drive. It locates and supports the chain along its ru...

Timing Chain Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing chain bears...

Water Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...

Gasket - Throttle

Idler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...

Fuel Injector Pipe Clamp for the high-pressure fuel injection system of the 3.0L V6 and 4.4L V8 (SDV8) diesel engines. The clamp secures a high-pr...

Oil Cooler Tube carries engine oil through the oil cooler circuit. The tube connects the engine oil system to the oil cooler, routing oil to be co...

O-ring for the variable valve timing (VVT) solenoid, part of the timing gear assembly at the front of the engine. The solenoid meters oil flow to ...

O-Ring - Radiator Hose

Crankcase Ventilation Tube for the 3.0L V6 diesel, part of the crankcase ventilation circuit and located at the oil pan. The tube forms the sectio...

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Gasket