Range Rover Sport L320 Parts

Relay - 20A 5-pin black micro-format relay for use in vehicle fuse and relay centres. The 5-pin configuration provides both normally-open and norm...

Spindle rod link

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Right-hand inlet manifold forming part of the air intake system, distributing charge air from the throttle and intake ducting evenly to the cylinde...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Tailgate Release Switch - micro-switch assembly fitted within the tailgate release mechanism. When operated, the switch provides the electrical sig...

Diff oil seal

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Fitment All Models From (V)6A916890

Stud

CV boot gaiter kit D3, D4, RRsp

ACE filter D2

Filter valve assy

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Compressor assy 9A (compressor only)

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Fitment: All Models 2.7 TDV6 To (V) 6A999999 2.7L TDV6 diesel models to (VIN) 6A999999

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...

Catalyst Gasket for the exhaust system of the 2.0L 16V Ti-VCT four-cylinder petrol engine. This gasket seals the joint at the catalytic converter ...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Front Brake Caliper Pin Kit covering both front calipers (left and right). The kit supplies the guide pin hardware required when servicing the fro...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Crankshaft Trigger Wheel Installer - a service tool for fitting the crankshaft trigger (reluctor) wheel to the crankshaft on the TDV6 engine. It l...

Key Fob Cover Kit provides a replacement outer cover for the remote key fob, renewing a housing that has become worn, cracked or faded. It restore...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Hose Intercooler - TDV6

Brake Caliper Piston for the rear hydraulic disc brake assembly. The piston sits within the caliper bore and transfers hydraulic pressure from the...

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

Arm front suspension with four corner air suspension RH lower

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Oil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

o-ring oil cooler 3,0 TDV6