Range Rover Sport L494 Parts

Valve Cover Stud and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The stud threads into the cylinder ...

O-Ring for the engine cooling system - it seals the water outlet tube at its connection to the cylinder block, alongside the thermostat housing. T...

Timing Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...

Ignition Coil generates the high-voltage output that fires the spark plug in the ignition system. One coil is fitted per cylinder in a coil-on-plu...

Valve Spring Retainer from the cylinder head valve train, the top cap that closes off the valve spring. It sits on top of the valve spring and is ...

Oil cooler seal, 9.5 mm diameter, sealing the small-bore oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diese...

Coolant Hose for the engine cooling circuit on supercharged petrol engines. A moulded coolant line with pre-formed bends, so it seats along its in...

Tube - Drain

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

EGR Cooler Filter - filter element fitted within the exhaust gas recirculation cooler assembly of the 3.0L V6 diesel Gen2 engine. Recirculated exh...

Timing Chain Tensioner Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing c...

Drive Chain Idler - timing gear idler sprocket for the 2.0L four-cylinder Ingenium engine family (AJ200 / AJ20 series, petrol and diesel). The idl...

Exhaust Manifold Gasket seals the exhaust manifold to the turbocharger on the 3.0L V6 diesel engine. Fitted at the manifold-to-turbocharger flange...

Cylinder Head Gasket seals the joint between the right-hand cylinder head and the engine block on the 3.0L DOHC supercharged GDI V6 petrol engine. ...

Cylinder Head Gasket for the left-hand cylinder head of the 3.0L DOHC GDI supercharged V6 petrol engine. Seals the machined joint between the left...

Wheel Cover set, fitted over the road wheels. The covers clip over the wheels to give a finished appearance and shield the wheel face from road di...

Wheel Cover for the road wheel. The cover fits over the wheel to give a finished appearance and shield the wheel face from road dirt and brake dus...

Diesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...

Idler Pulley for the accessory drive belt system, mounted on the front of the engine within the auxiliary belt run. The idler pulley drives nothin...

Crankshaft Gear, the timing drive gear that mounts on the front of the crankshaft within the timing cover. It drives the timing chain, transferring...

Crankshaft Seal and Retainer - the rear crankshaft oil seal complete with its retainer housing, sealing the rear of the crankshaft where it exits t...

Front Crankshaft Oil Seal - radial lip seal in the cylinder block and front cover assembly, sealing the crankshaft nose where it passes through the...

EGR Gasket Inlet

Primary Fuel Filter for the diesel fuel supply system. Positioned upstream of the high-pressure injection circuit, it removes particulate contamina...

Differential Mounting Insulator, a bush-type isolator in the front differential mounting. The insulator locates the front differential to the axle...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Engine Mount Insulator for the engine and transmission mounting system. The insulator is the rubber-and-metal mount that supports the powertrain o...

Anti-Roll Bar Link connects the front anti-roll bar to the suspension, part of the front stabilizer bar assembly. It transfers movement between th...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Drive Belt Idler Pulley - a non-driven guide pulley in the accessory drive belt system of the 3.0L AJ20P6 six-cylinder petrol engine. The idler gu...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Tailgate Switch operates within the powered tailgate and luggage compartment locking controls. The switch signals tailgate release, actuating the ...

Exhaust downpipe gasket sealing the flanged joint between the front exhaust pipe (downpipe) and the catalytic converter, in the front section of th...

Exhaust downpipe gasket sealing the flanged joint between the front exhaust pipe (downpipe) and the catalytic converter, in the front section of th...

Cylinder Head Gasket sealing the cylinder head to the engine block. Fitted to the 2.0L four-cylinder AJ200 (Ingenium) petrol engine, including PHE...

Spark Plug Aperture Gasket seals the spark plug aperture in the cylinder head cover on the left hand cylinder bank. It closes the joint between th...

Chain - Timing

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

O-Ring seals the variable valve timing (VVT) solenoid within the timing gear and sprocket assembly. It maintains an oil-tight joint between the VV...

Turbo Oil Return Hose Gasket seals the upper joint of the turbocharger oil return hose, where the hose meets the turbocharger housing in the engine...