Range Rover Velar Parts L560

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Locking Flange Nut - M8 for fastening applications requiring vibration-resistant fixings. A prevailing-torque hexagonal nut with an integral flang...

Injector Bolt secures the fuel injector clamp within the cylinder head on the 2.7 and 3.0 V6 diesel engines. The M6 x 35 mm bolt retains the clamp...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Wheel Nut for securing an alloy road wheel to the hub. It threads onto the wheel stud and clamps the wheel against the hub mounting face, providing...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Left-hand inlet manifold for the 3.0L V6 diesel engine induction system. The manifold distributes intake air from the charge air system into the ...

Oil Separator is part of the crankcase ventilation system on the 3.0L V6 diesel engine, separating oil mist from crankcase blow-by gases. The sepa...

Throttle Housing Seal for the 2.7L TDV6 and 3.0L SDV6 diesel engines, sealing the throttle body to the air intake. The seal sits between the throt...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Fuel return tube O-ring seal

Steering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Telematics Control Unit Backup Battery, a lithium-ion cell that supplies the Telematics Control Unit (TCU) when the main vehicle battery is disconn...

Camshaft Position Sensor within the engine management system of the 3.0L diesel engine. This sensor monitors camshaft rotational position and tran...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Valve - Control

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

o-ring oil cooler 3,0 TDV6

Latch hood, bonnet, RH and LH, with sensor

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Accessory Drive Idler Pulley

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Transmission Oil Pan & Filter Kit - the lower fluid pan for the ZF 8HP70 8-speed automatic transmission, incorporating an integrated fluid filt...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

EGR Outlet Gasket for the 2.0L four-cylinder diesel engine (AJ200), sealing the joint where the EGR valve outlet meets the inlet manifold. It main...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Cylinder Head Gasket for the right-hand cylinder bank of the 3.0L supercharged V6 petrol engine (DOHC GDI). It seals the cylinder head to the engin...

Vacuum Pump Gasket sealing the vacuum pump to the engine. Forms the joint between the vacuum pump and its mounting face, maintaining the seal for ...

Cylinder Head Gasket for the 5.0L V8 AJ133 petrol engine. The gasket seals the joint between a cylinder head and the engine block, containing comb...

Cylinder Head Gasket for the left-hand cylinder bank of the 3.0L supercharged V6 petrol engine (DOHC GDI). It seals the cylinder head to the engine...

Windscreen Wiper Blade for the front wiper assembly. Clears rain and road spray from the windscreen, mounted to the wiper arm within the wash/wipe...

Water Connection for the turbocharger coolant feed, lower position, in the turbocharger lubrication and cooling circuit of the 3.0L AJ20P6 Ingenium...

Crankcase cover gasket for the crankcase ventilation (emission control) cover on the 3.0L Ingenium six-cylinder petrol engine - AJ20P6 / AJ22P6, in...

Spark Plug - ignition spark plug for Ingenium petrol engines (AJ20 / AJ22 series, including PHEV applications). The plug screws into the cylinder ...