Range Rover Velar Parts L560

Clip secures an exterior body moulding to the body panel. It is a retaining clip used in the body moulding assembly, holding a trim moulding in po...

EGR Outlet Gasket seals the outlet joint of the exhaust gas recirculation (EGR) system, where recirculated exhaust gas leaves the EGR valve/cooler ...

Valve Spring Seat is the seat on the cylinder head that locates the base of the valve spring, providing the surface against which the spring is com...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...

Intake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Cover Gasket for the upper timing chain cover. It seals the joint between the upper timing chain cover and the engine, maintaining an oil-tight se...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Tensioner Arm for the engine timing gear. It bears against the timing chain and transmits the tensioner load to take up slack and mai...

Special Bolt for the engine timing gear assembly. It secures a component within the timing gear drive. Fitted to 2.0-litre diesel Ingenium engines...

Exhaust Manifold Gasket sealing the exhaust manifold and turbocharger joint. The same gasket serves both the exhaust manifold and the turbocharger...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Water Outlet Tube forming the coolant outlet connection at the cylinder head, part of the engine cooling circuit. It carries coolant from the cyli...

O-Ring for the turbocharger of the 2.0L I4 diesel (AJ200) engine, sealing the upper turbocharger-to-pipe joint (14.3 x 2.4 mm). The O-ring seals t...

Cylinder Head Bolt with hex head, for the 2.0L I4 diesel (AJ200) engine. The bolt secures the cylinder head to the engine block, providing the cla...

Turbocharger Gasket for the exhaust turbocharger assembly on the 2.0L I4 diesel (AJ200) engine, sealing the turbocharger outlet to the exhaust fron...

Exhaust Manifold Gasket for the 3.0L V6 diesel engine, sealing the exhaust manifold to the cylinder head. It forms the gas-tight seal at the manif...

Wheel Centre Cap for the alloy road wheel. This cover fits to the hub centre of the alloy wheel, closing off the centre bore and completing the wh...

Timing Chain Bolt, M12 x 1.5 x 40mm, for the 3.0L V6 diesel engine. This bolt secures components of the timing chain drive at the front of the eng...

Breather Tube for the crankcase ventilation system of the 3.0L supercharged V6 petrol engine. It routes crankcase blow-by gases from the engine as ...

Hex Head Bolt securing the timing belt idler pulley at the lower timing gear of the 3.0L V6 diesel engine. This is a single fixing bolt for the id...

Chain Lubricating Jet is an oil spray jet in the timing drive of the 3.0L V6 supercharged and 5.0L V8 petrol engines. Installed behind the front c...

Crankcase Breather Tube for the crankcase ventilation system on the 3.0L V6 Supercharged Petrol. This tube routes crankcase blow-by gases from the...

Transmission Fluid is the specified fluid for the electronically controlled all-wheel-drive coupling (Haldex-type) used on transverse-engine models...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Lever - Bonnet Release

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Coolant Hose - throttle body heater outlet hose within the engine cooling circuit. The hose routes engine coolant from the throttle body heater ou...

Intake Manifold Gasket - the upper intake manifold gasket for the 3.0L supercharged V6 petrol engine. It seals the upper intake manifold joint, ke...

Inlet Valve - a cylinder head intake valve for the 3.0L supercharged V6 petrol engine. It seats in the cylinder head intake port and opens on the ...

Timing Gear Bolt - the upper fixing bolt for the timing gear drive on the 3.0L V6 diesel engine. It secures the upper timing gear within the engin...

Lower Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the lower section of the inlet manifold to the cylinder head, seal...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Timing Chain Lubricating Oil Jet for the timing drive of the 5.0L V8 petrol engine (AJ133, naturally aspirated and supercharged). The jet feeds pr...

Auxiliary Drive Chain for the AJ133 5.0L V8 and 3.0L V6 supercharged petrol engines. It forms part of the engine's chain drive assembly, running a...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...

Oil Cooler Tube forms part of the engine oil cooling circuit, carrying oil between the engine and the oil cooler. Used on 5.0L V8 and 3.0L V6 supe...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...