Range Rover Velar Parts L560

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Lever - Bonnet Release

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Timing Gear Bolt - the upper fixing bolt for the timing gear drive on the 3.0L V6 diesel engine. It secures the upper timing gear within the engin...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Timing Chain Lubricating Oil Jet for the timing drive of the 5.0L V8 petrol engine (AJ133, naturally aspirated and supercharged). The jet feeds pr...

Auxiliary Drive Chain for the AJ133 5.0L V8 and 3.0L V6 supercharged petrol engines. It forms part of the engine's chain drive assembly, running a...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...

Oil Cooler Tube forms part of the engine oil cooling circuit, carrying oil between the engine and the oil cooler. Used on 5.0L V8 and 3.0L V6 supe...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Valve Cover Screw and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The screw secures the camshaft (va...

Oil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...

Lower chain guide for the auxiliary drive chain, part of the timing gear assembly on the 5.0L V8 petrol engine (AJ133). The guide runs against the...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Inlet Manifold Gasket for the left-hand cylinder bank of the 5.0 litre V8 petrol engine (AJ133). It seals the joint between the inlet manifold and ...

O-ring for the engine oil cooler and oil filter housing assembly, sealing the top oil cooler hose connection on the 3.0L V6 diesel. It seals the j...

Coolant Pipe - Lower Radiator is a connector tube in the bottom radiator hose run of the engine cooling system. It joins two sections of the lower...

Oil cooler seal, 18 mm diameter, sealing an oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diesel. Three are...

Automatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...

Valve Cover Stud and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The stud threads into the cylinder ...

Timing Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...

Camshaft Cover Gasket - LH seals the left-hand camshaft cover to the cylinder head on the AJ133 5.0L V8 petrol engine. It closes the joint around ...

Valve Spring Retainer from the cylinder head valve train, the top cap that closes off the valve spring. It sits on top of the valve spring and is ...

Oil cooler seal, 9.5 mm diameter, sealing the small-bore oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diese...

Tube - Drain

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

Timing Chain Tensioner Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing c...

Exhaust Manifold Gasket seals the exhaust manifold to the turbocharger on the 3.0L V6 diesel engine. Fitted at the manifold-to-turbocharger flange...

Crankshaft Seal and Retainer - the rear crankshaft oil seal complete with its retainer housing, sealing the rear of the crankshaft where it exits t...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Breather Valve for the axle case or manual transmission housing. The valve vents the housing to atmosphere, allowing internal air pressure to equa...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Breather Tube forming part of the crankcase ventilation circuit on the 5.0L V8 petrol engine (AJ133). It carries crankcase blow-by gases from the ...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...