Range Rover Velar Parts L560

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Oil Pump Gasket that seals the oil pump to the cylinder block within the engine lubrication system, for the 3.0L V6 diesel engine. It maintains th...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Vacuum Pump Gasket sealing the vacuum pump to the engine. Forms the joint between the vacuum pump and its mounting face, maintaining the seal for ...

O-Ring - seals the upper joint of the thermostat housing. Fitted to 3.0L supercharged V6 and 5.0L V8 petrol engines, it maintains a leak-tight coo...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Camshaft Cover Gasket - the sealing gasket between the camshaft (cylinder head) cover and the cylinder head. It seals the cam cover to the head to...

Flywheel Bolt - hex head fastener that secures the flywheel to the rear crankshaft flange within the engine driveline assembly. Fitted to the 3.0L...

Oil Return Hose - the oil drain hose in the turbocharger lubrication circuit. It returns oil from the turbocharger bearing housing to the sump aft...

Valve Spring Seat is the seat on the cylinder head that locates the base of the valve spring, providing the surface against which the spring is com...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...

Exhaust Manifold Gasket for the 3.0L V6 diesel engine, sealing the exhaust manifold to the cylinder head. It forms the gas-tight seal at the manif...

Wheel Centre Cap for the alloy road wheel. This cover fits to the hub centre of the alloy wheel, closing off the centre bore and completing the wh...

Timing Chain Bolt, M12 x 1.5 x 40mm, for the 3.0L V6 diesel engine. This bolt secures components of the timing chain drive at the front of the eng...

Breather Tube for the crankcase ventilation system of the 3.0L supercharged V6 petrol engine. It routes crankcase blow-by gases from the engine as ...

Hex Head Bolt securing the timing belt idler pulley at the lower timing gear of the 3.0L V6 diesel engine. This is a single fixing bolt for the id...

Chain Lubricating Jet is an oil spray jet in the timing drive of the 3.0L V6 supercharged and 5.0L V8 petrol engines. Installed behind the front c...

Crankcase Breather Tube for the crankcase ventilation system on the 3.0L V6 Supercharged Petrol. This tube routes crankcase blow-by gases from the...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Lever - Bonnet Release

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Coolant Hose - throttle body heater outlet hose within the engine cooling circuit. The hose routes engine coolant from the throttle body heater ou...

Timing Gear Bolt - the upper fixing bolt for the timing gear drive on the 3.0L V6 diesel engine. It secures the upper timing gear within the engin...

Lower Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the lower section of the inlet manifold to the cylinder head, seal...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Timing Chain Lubricating Oil Jet for the timing drive of the 5.0L V8 petrol engine (AJ133, naturally aspirated and supercharged). The jet feeds pr...

Auxiliary Drive Chain for the AJ133 5.0L V8 and 3.0L V6 supercharged petrol engines. It forms part of the engine's chain drive assembly, running a...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...

Oil Cooler Tube forms part of the engine oil cooling circuit, carrying oil between the engine and the oil cooler. Used on 5.0L V8 and 3.0L V6 supe...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Valve Cover Screw and Sleeve from the cylinder head cover fixings of the petrol V8 and supercharged V6 engines. The screw secures the camshaft (va...

Oil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...

Lower chain guide for the auxiliary drive chain, part of the timing gear assembly on the 5.0L V8 petrol engine (AJ133). The guide runs against the...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...