Range Rover Velar Parts L560

Exhaust Crossover Pipe for the 3.0L V6 diesel, part of the front exhaust assembly. It carries exhaust gas from one cylinder bank across the engine ...

Combined Oil and Vacuum Pump for the 2.0L Ingenium (AJ200) diesel engine. This tandem unit houses the engine oil pump and the vacuum pump in a sing...

Throttle Body and Motor in the engine air intake system, supplied with an integral electric actuator motor. On this 3.0L V6 diesel, the throttle b...

NOx Trap Temperature Sensor within the diesel exhaust aftertreatment system. Mounted in the exhaust stream at the NOx trap, the sensor reports exh...

Supercharger Kit - the belt-driven positive-displacement supercharger for the 3.0L DOHC GDI V6 petrol engine, mounted in the vee of the block to pr...

Shock Absorber - a rear suspension shock absorber, the damping element controlling movement at the rear of the vehicle. Mounted between the body a...

High Voltage Water Heater for plug-in hybrid (PHEV) applications, operating in the high-voltage coolant heating circuit. The unit heats engine coo...

Air Suspension Compressor The pump that generates and supplies compressed air to the four-corner electronic air suspension system. Driven by an el...

Air Suspension Compressor from the air supply unit of the four-corner electronic air suspension system. The compressor draws in ambient air, compr...

Front Shock Absorber - left-hand side, part of the front suspension damper assembly. The damper controls spring and wheel movement at the front ax...

Front Shock Absorber - right-hand side, part of the front suspension damper assembly. The damper controls spring and wheel movement at the front a...

Turbocharger for the 2.0L AJ200 / AJ20D4 four-cylinder diesel engine. It sits in the forced-induction circuit between the exhaust manifold and the...

Cylinder Head Gasket - 5.0L V8 seals the joint between the cylinder head and the engine block on the 5.0L V8 petrol engine. It maintains the seal ...

Cooling Turbo Gasket

Washer - Sealing

Relay Black 2A 4 Pin

Fuel Pump Drive Control module within the fuel delivery system, governing operation of the in-tank fuel pump. The module receives a demand signal ...

Fuel Pump Drive Control module within the fuel delivery system, governing operation of the in-tank fuel pump. The module receives a demand signal ...

Purge Control Valve - evaporative emission (EVAP) control system. The valve sits in the line between the activated carbon canister and the engine ...

Leak-Off Tube - Injection Pump

Kit - Drive Belt

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

EGR Unit for the exhaust gas recirculation system, mounted on the right-hand side and fed from the exhaust manifold. The exhaust gas recirculation...

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Fuel Injector Sealing Washer for diesel injector installations. The washer seals the fuel injector against its seat in the cylinder head, containi...

Inlet Manifold distributes incoming charge air to the cylinder head inlet ports, forming part of the air intake system on the 3.0L V6 diesel engine...

Primary Fuel Filter - diesel fuel supply circuit, mounted in-line in the fuel lines between the tank and the engine. As the first filtration stage...

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Wheel Bearing - Rear, a component of the rear hub assembly. The rear wheel bearing carries the vehicle's rear load and allows the road wheel and h...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

O-Ring and Grease Kit for servicing the transfer box input shaft. Contains the input shaft O-ring and the anti-seize grease used when resealing th...