Range Rover Velar Parts L560

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Nut for U-bolt M12

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

ATF - Dexron III is an automatic transmission fluid meeting the Dexron III specification, supplied in a 5 litre container. It is a hydraulic fluid...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Pollen & Odour Filter - the cabin air filter in the HVAC intake system. It sits in the fresh-air path upstream of the blower, cleaning the air ...

Oil Filter - a replaceable oil filter element housed within the engine oil cooler and filter assembly of the 3.0L V6 turbo diesel (TD6) engine. Th...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Injector O-Ring is the lower sealing ring for a diesel fuel injector, used on 3.0L SDV6 and 4.4L TDV8 engines. It seals the lower body of the inje...

Oil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...

Diesel Exhaust Fluid (AdBlue) is a consumable fluid for the Selective Catalytic Reduction (SCR) exhaust aftertreatment system on diesel engines. I...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Relay - 20A 5-pin black micro-format relay for use in vehicle fuse and relay centres. The 5-pin configuration provides both normally-open and norm...

Air Suspension Connector joins the valve block to a high-pressure air line within the air suspension pneumatic circuit. The fitting forms a sealed...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

EGT Sensor Exhaust gas temperature sensor in the exhaust and emissions aftertreatment system of the 3.0L V6 diesel engine. It measures exhaust gas...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

Kit for the fuel injection pump drive system within the engine front timing drive assembly. It operates as part of the auxiliary timing arrangeme...

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Timing gear lower idler pulley for the engine timing drive system. This pulley guides and stabilizes the timing belt within the lower timing gear...

Oil Pressure Switch for the engine lubrication system on Td6 2.7 and 3.0 diesel engines. The switch is threaded into the engine block and monitors ...

Oil Pressure Switch for the engine lubrication system on Td6 2.7 and 3.0 diesel engines. The switch is threaded into the engine block and monitors ...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Gasket - Exhaust Manifold

Exhaust Gas Pressure Sensor for the 3.0L AJ20D6 Ingenium six-cylinder turbo diesel, operating within the exhaust gas recirculation and aftertreatme...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Guide - Timing Chain

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

Drive Belt for the accessory drive at the front of the engine. A multi-ribbed poly-V belt that takes drive from the crankshaft pulley and turns th...

Drive Chain Idler - timing gear idler sprocket for the 2.0L four-cylinder Ingenium engine family (AJ200 / AJ20 series, petrol and diesel). The idl...

Drive Belt - V-belt in the front-end accessory drive of the 3.0L Ingenium six-cylinder petrol engine, driving the belt-integrated starter generator...

O-Ring for the high-pressure diesel fuel injection pump. The ring seals the joint between the pump body and its mounting face on the engine, preve...

DEF Injector Refit Kit

Exhaust Manifold Bolt for the 3.0L V6 diesel engine, securing the exhaust manifold to the cylinder head. The bolt works in a high-temperature, hig...

Front Crankshaft Oil Seal for the Ingenium engine family, sealing the crankshaft nose where it passes through the front cover. The seal runs on th...