for Discounts / VAT
for Discounts & Correct VAT
Replacement parts for the Range Rover Velar L560, built at Solihull from 2017 on the JLR iQ[Al] aluminium platform. Covers all Ingenium diesel and petrol variants, MHEV, PHEV, and ZF 8-speed automatic configurations.
Exhaust Manifold Gasket for the 3.0L V6 diesel engine, sealing the exhaust manifold to the cylinder head. It forms the gas-tight seal at the manif...
View full detailsCrankshaft Gear in the engine timing drive of the supercharged petrol V6 and V8 engines. Mounted on the nose of the crankshaft, it drives the timi...
View full detailsWheel Centre Cap for the alloy road wheel. This cover fits to the hub centre of the alloy wheel, closing off the centre bore and completing the wh...
View full detailsTiming Chain Bolt, M12 x 1.5 x 40mm, for the 3.0L V6 diesel engine. This bolt secures components of the timing chain drive at the front of the eng...
View full detailsTiming Chain Bolt, M12 x 1.5 x 40mm, for the 3.0L V6 diesel engine. This bolt secures components of the timing chain drive at the front of the eng...
View full detailsEGR Tube Clamp used in the exhaust gas recirculation (EGR) system to secure the EGR tube connection. For 3.0L V6 diesel applications.
Coolant Temperature Sensor mounted in the cylinder head, measuring engine coolant temperature. The sensor provides the temperature signal used by ...
View full detailsBreather Tube for the crankcase ventilation system of the 3.0L supercharged V6 petrol engine. It routes crankcase blow-by gases from the engine as ...
View full detailsGasket - Turbocharger Cooling
Hex Head Bolt securing the timing belt idler pulley at the lower timing gear of the 3.0L V6 diesel engine. This is a single fixing bolt for the id...
View full detailsHex Head Bolt securing the timing belt idler pulley at the lower timing gear of the 3.0L V6 diesel engine. This is a single fixing bolt for the id...
View full detailsPipe - Fuel
Chain Lubricating Jet is an oil spray jet in the timing drive of the 3.0L V6 supercharged and 5.0L V8 petrol engines. Installed behind the front c...
View full detailsCrankcase Breather Tube for the crankcase ventilation system on the 3.0L V6 Supercharged Petrol. This tube routes crankcase blow-by gases from the...
View full detailsBrake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...
View full detailsBrake Fluid - DOT 4 low-viscosity hydraulic brake fluid, supplied in a 1 litre container. It transmits pedal pressure through the hydraulic brakin...
View full detailsSpark Plug - ignites the air-fuel mixture in the combustion chamber. Provides the timed spark that initiates combustion as part of the ignition sy...
View full detailsTiming Chain Guide that locates and supports the timing chain along its run within the timing drive. It controls the chain path and reduces vibrat...
View full detailsTiming Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...
View full detailsTiming Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...
View full detailsTiming Chain Guide for the primary timing chain, fitted on the right-hand side of the timing drive. It locates and supports the chain along its ru...
View full detailsTiming Chain Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing chain bears...
View full detailsOil - Lubricant
Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...
View full detailsCoolant Hose carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It runs f...
View full detailsWater Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...
View full detailsGasket - Throttle
Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...
View full detailsFuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...
View full detailsIgnition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...
View full detailsIgnition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...
View full detailsUpper Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the joint at the upper section of the two-piece inlet manifold, ma...
View full detailsCoolant Hose - throttle body heater outlet hose within the engine cooling circuit. The hose routes engine coolant from the throttle body heater ou...
View full detailsTailgate Switch operates within the powered tailgate and luggage compartment locking controls. The switch signals tailgate release, actuating the ...
View full detailsLower Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the lower section of the inlet manifold to the cylinder head, seal...
View full detailsIntake Manifold Gasket - the upper intake manifold gasket for the 3.0L supercharged V6 petrol engine. It seals the upper intake manifold joint, ke...
View full detailsInlet Valve - a cylinder head intake valve for the 3.0L supercharged V6 petrol engine. It seats in the cylinder head intake port and opens on the ...
View full detailsTiming Gear Bolt - the upper fixing bolt for the timing gear drive on the 3.0L V6 diesel engine. It secures the upper timing gear within the engin...
View full detailsUpper Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the joint at the upper section of the two-piece inlet manifold, ma...
View full detailsIdler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...
View full detailsLower Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the lower section of the inlet manifold to the cylinder head, seal...
View full detailsLower Inlet Manifold Gasket for the supercharged 3.0L V6 petrol engine. It seals the lower section of the inlet manifold to the cylinder head, seal...
View full detailsInlet Valve for the supercharged 3.0L V6 petrol engine (AJ126). The inlet valve seals against its seat in the cylinder head and opens on the intake...
View full detailsFuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...
View full detailsFuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...
View full detailsIdler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...
View full detailsBolt for the suspension mountings. Secures front and rear suspension arms, struts and springs at their attachment points under suspension loads.
Bolt for the suspension mountings. Secures front and rear suspension arms, struts and springs at their attachment points under suspension loads.
The Velar L560 has been produced with a wider engine range than most single-generation Land Rover models, and correct part fitment depends on knowing your engine code and model year. The pre-facelift range ran from 2017 to 2020 and included the Ingenium D180 and D240 four-cylinder diesels, the twin-turbo D300 and D275 V6 diesels, the P250 and P300 four-cylinder petrols, the P340 and P380 supercharged V6 petrols, and the limited SVAutobiography Dynamic with the 5.0-litre V8. From September 2020, the engine range was revised. The D200 replaced the D180 with mild hybrid assistance, the P400 Ingenium turbocharged inline-six replaced the P380 V6, and the P400e PHEV was introduced, combining a 2.0-litre Ingenium petrol unit with a 106 kW permanent magnet synchronous motor and a 17.1 kWh lithium-ion battery. A mild exterior and infotainment refresh was applied from 2023. Fitment differences exist between pre-facelift, post-September-2020, and post-2023 vehicles, particularly for engine ancillaries, emissions components, and hybrid system parts.
All four-cylinder variants use the ZF 8HP45 eight-speed automatic gearbox. All six-cylinder variants use the heavier-duty ZF 8HP70 unit. Gearbox-related parts must be matched to the correct variant.
Engine specifications and ZF 8HP transmission variant assignments confirmed against ZF Group 8HP-series technical data and JLR engine specifications as documented in the Range Rover Velar L560 launch technical record.
The Velar L560 shares its iQ[Al] D7a aluminium platform with the Jaguar F-Pace, Jaguar XF (X260), and Jaguar XE. This means a number of underbody, suspension geometry, and fastener components are shared across those vehicles. Workshops sourcing parts for the Velar may find that certain subframe components, suspension bushings, and general hardware are catalogued across both JLR and Jaguar parts systems. This does not apply to powertrain-specific or model-specific body parts. Always confirm part numbers against the Velar L560 catalogue before ordering on the basis of platform compatibility alone.
Fitment ConfirmationThe Velar L560's broad engine and drivetrain range means that year-of-manufacture alone is not sufficient to confirm fitment for many parts. The Vehicle Identification Number (VIN) contains the production sequence, engine code, and build specification and is the most reliable way to confirm the correct part for your vehicle. The VIN is located on the windscreen lower edge (driver's side on most LHD markets, passenger's side on RHD markets) and on the vehicle's identification plate in the engine bay. If you are unsure whether a listed part fits your specific Velar, contact Budget Parts with your VIN before ordering.
Related CollectionsFor parts covering other Range Rover generations or the broader Range Rover family, see Range Rover parts.
For Velar-adjacent models built on the same generation platform, the Range Rover Evoque L538 parts collection covers the previous Evoque generation and the Range Rover Sport L494 parts collection covers the Sport generation sharing the same era of Ingenium engine development.
Technical GuidesThe following article from the Budget Parts technical library covers the Velar L560 platform, engines, and ownership considerations relevant to parts selection.
A technical reference covering the iQ[Al] D7a platform, Ingenium engine range, AWD systems, and the service considerations that affect accurate parts selection on the Velar L560.
Range Rover Velar L560 guide →The Range Rover Velar L560 entered production in 2017 and is the only current generation of the Velar. A mild facelift was introduced in 2023, primarily affecting exterior styling and the infotainment system. A second-generation Velar on a new electric-only platform is announced for production from 2027 and is a separate vehicle entirely. Parts on this page cover the L560 generation only, from 2017 to present.
The engine code is stamped on the engine block and is also encoded in your VIN. For diesel variants, the main codes in service are D180 (2017 to 2020), D200 (2020 onwards, MHEV), D240 (2017 to 2020), D300 V6 (2017 to 2020), and D300 Ingenium inline-six (2020 onwards). For petrol variants, the main codes are P250, P300 (2017 to 2020), P340, P380 (2017 to 2020), P400 MHEV (2020 onwards), and P400e PHEV (2020 onwards). Engine-specific parts including timing components, injectors, and turbo ancillaries must be matched to the correct code.
Yes, in part. Both vehicles are built on the JLR iQ[Al] D7a aluminium platform, sharing the same wheelbase of 2,874 mm and common underbody architecture. This means certain suspension geometry components, subframe hardware, and general fasteners are shared across the catalogue. However, powertrain-specific parts, body panels, and model-specific electronics are not interchangeable. Workshops cross-referencing parts between the Velar and F-Pace should always verify against the Velar L560 part number before ordering.
All Velar L560 variants use a ZF 8-speed automatic transmission. Four-cylinder engines (diesel and petrol) are paired with the ZF 8HP45 unit. Six-cylinder engines, including the P380, P400, D300 V6, and D300 I6, are paired with the heavier-duty ZF 8HP70 unit. Gearbox-related parts, including oil, filter kits, solenoids, and sensors, must be matched to the correct 8HP variant for your engine.
Genuine parts carry the official Land Rover part number and are manufactured to JLR specification. OEM parts are produced by the same manufacturer that supplied the component to JLR originally, meeting the same specification without the Land Rover branding. Aftermarket parts are independently manufactured and are suitable for wear items and general maintenance where exact OEM specification is not required. All three tiers are available through Budget Parts for the Velar L560.
Use your VIN. The 17-character VIN encodes your engine code, production year, and build specification and is the most reliable way to confirm fitment before ordering. The VIN is located on the lower edge of the windscreen (driver's side on most LHD markets, passenger's side on RHD markets) and on the identification plate in the engine bay. If you need help confirming fitment, contact Budget Parts with your VIN and the part reference you are considering.
Yes. The collection includes parts relevant to the P400e PHEV (introduced September 2020) and D200 and P400 MHEV variants. These include hybrid system ancillaries, AdBlue components for diesel MHEV variants, and Ingenium engine parts common to the hybrid-equipped models. Specific high-voltage battery components are not included in this collection. Contact Budget Parts if you are sourcing parts for a specific PHEV or MHEV repair and are unsure whether a listed part applies to your variant.