Land Rover Parts

Brake Pipe Set Defender(90) 1992 Onwards LHD

Brake Pipe Set - a complete set of pre-formed rigid brake pipes for the hydraulic braking circuit, shaped for left-hand-drive (LHD) routing. Repla...

Rear Drum Brake Kit, supplied as a single-axle service set for the rear drum brakes. The kit includes the brake shoes, wheel cylinders, brake spri...

Brake Kit - a complete rear drum brake overhaul set for the short-wheelbase rear axle, covering both sides in a single kit. It renews the main fri...

Brake Kit - front axle, short-wheelbase (88-inch), covering both sides. Renews the front drum brake components: brake shoes, wheel cylinders, retu...

48 Spline Boss - Defender Fa On

Polyurethane Ball Joint Boots for the front axle upper and lower ball joints. These flexible boots seal over the ball joint to retain grease and ke...

Footwell Repair Panel 2&3 LHD - Series - RH

LH Footwell Repair Panel - Series 2/3 LHD

Spring Shackle Plate Kit - 1-Ton - Front

Snorkel Head is the 3" ram-air intake head that fits to the top of a raised air intake tube, forming the forward-facing scoop that feeds cool, clea...

Chubby Cubby Box - a between-seats storage box and armrest that mounts on the centre panel of the seat box. It provides lockable interior storage ...

Polyurethane Bush Kit for the steering damper mountings, replacing the original rubber bushes that locate the damper at its fixing points. Moulded...

Rear Wheel Bearing Kit containing the parts needed to overhaul one rear hub bearing assembly. The taper roller bearings carry the rear hub on the s...

Spare Wheel Carrier Hinge Bush - a pair of nylon bushes for the swing-away spare wheel carrier (DA2232 / GA2232). The bushes line the hinge pivot ...

Weber Carburettor Conversion for the 2.25L petrol engine, replacing the original Solex carburettor. This progressive downdraught Weber unit instal...

Dash Repair Kit is an interior dashboard trim kit, finished in brown, that covers the front edge of the dashboard. It addresses the peeling and cu...

Screw Kit - stainless steel screws for fixing a side air intake grille to the front wing. The set contains five stainless steel screws and serves ...

Bonnet Vent Grille Set - a pair of top-vent grilles that replace the original bonnet top vents, providing ventilation openings through the bonnet p...

Ball Joint Separator (Fork) is a hand tool for separating a tapered ball joint from its mating arm, such as a track rod end from the steering arm. ...

Trim Tool Set is a 12-piece kit for removing interior and exterior trim panels, mouldings and clip fasteners without damaging the surrounding surfa...

Fulcrum Bracket & Ball Joint Assembly - Adjustable forms the apex mounting of the rear A-frame - the triangulated top link that locates the rea...

Side Window Filler Strip for the rear side window assembly. The filler strip closes the gap along the side window channel, completing the seal and...

Radius Arm Bush is a polyurethane bush located at the front radius arm's chassis mounting. It locates the radius arm to the chassis while allowing...

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Screw for body and interior trim fixing - a No.12 x 1/2" pan-head screw. Used to secure body panels, dash and facia, wheelarch and interior trim. ...

Engine Dowel, a precision locating dowel that sets the relative position of mating engine components during assembly. The dowel fixes the exact al...

Fuel Pipe for the fuel supply circuit, running to the carburettor. It carries fuel from the fuel pump outlet to the carburettor inlet on the 2.25L...

Road Spring SWB Rear 11L

Ignition Coil Pack in the engine ignition system, generating the high-tension voltage that fires the spark plugs. Used on the distributorless V8 e...

Bulb & Holder - Main Instrument Panel for the Discovery 2 instrument cluster illumination circuit. This bulb and holder assembly fits into the...

Speedometer for the instrument cluster, displaying road speed with LED illumination. It mounts in the dashboard instrument panel, indicating vehic...

Ride Height Sensor is a rotary position sensor in the electronic air suspension system, mounted at the front right-hand corner. It links to the su...

Front Wheelarch is a body panel that forms the wheel housing around the front wheel on the right-hand (RH) side. It encloses the upper and rear fa...

Exhaust rear silencer LR90 def TD5 Stainless steel

Rear Air Conditioning Resistor Assembly for the rear blower (HVAC) circuit on vehicles equipped with rear air conditioning. The resistor pack sits...

Mounting Rubber for the air suspension air supply unit - the combined compressor and valve block assembly. This rubber isolator mount fits between...

Battery Isolator Switch - key-operated master cut-off switch for the vehicle electrical system, rated at 300A. Wired inline on the main battery le...

Oil Filter Housing Gasket seals the oil filter housing cover within the engine oil filtration assembly. It forms the joint between the filter hous...

Front Cover Drain Plate - part of the engine front (timing) cover assembly. It closes and seals the drain aperture at the base of the front cover. ...

Module - relay and diode pack serving the fuel injection electrical circuit. It controls and protects the power supply feeding the electronic petro...

Rocker Cover Gasket seals the rocker (cam) cover to the cylinder head on the 2.5L six-cylinder diesel. It runs around the cover flange to contain ...

Hub Cap for the 101 Forward Control wheel hub. Fits the wheel hub on Series II, IIA, and III 101 Forward Control variants, covering and protecting...

Engine Sensor Wiring Harness - short link lead within the engine management wiring of the 1.8L K Series petrol engine. It connects the camshaft po...