Land Rover Parts

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Rear Anti-Roll Bar Bolt secures the rear anti-roll bar within the rear suspension assembly. It fixes the bar to its mounting, holding it in positi...

Hex Head Bolt - M6 x 20mm flanged bolt used as a general-purpose fixing at numerous points on the vehicle. The integral flange spreads the clampin...

Plain Washer from the anti-roll bar mounting hardware. It spreads the clamping load of the anti-roll bar fixing across the mounting face, protecti...

Sealing Washer - a sealing washer used at the front suspension strut mounting. It seats at the strut fixing to seal and settle the joint while mai...

ACE Seal Kit for the Active Cornering Enhancement valve block. The ACE system operates hydraulic actuators on the front and rear anti-roll bars to...

Pivot Pin a machined clevis-type pin that forms the hinged joint between a linkage rod and its bracket or lever. The pin passes through the clevis...

Piston Rings - 200TDi - Standard for the 2.5L 200TDi four-cylinder turbo-diesel engine at standard bore dimensions, for use during engine overhaul....

Piston Assembly for the 2.5 four-cylinder naturally aspirated diesel, machined +0.040 in oversize. The piston transfers combustion pressure to the...

Rear Body Side Panel Assembly - outer bodyside panel forming the rear quarter of the load area, part of the lower rear body structure. The panel c...

Plain Washer - flat load-spreading washer, 5/8 in (15.9 mm) outside diameter with a 5/16 in (7.9 mm) bore. Fitted under a bolt head or nut, the wa...

Transfer Box Ball Bearing for the Borg Warner transfer gearbox, supporting the front output flange and viscous coupling and the rear output shaft. ...

Clutch Hose for the clutch hydraulic circuit, carrying fluid from the rigid pipe run to the slave cylinder on the bellhousing. The flexible sectio...

Brake Caliper - Rear - RH - 7/16" UNF Mounting

Track Rod End ball joint for the front steering linkage, forming the articulating connection between the steering rod and the steering arm on the s...

Hexagonal Screw - sump pan retaining screw for the ZF four-speed automatic transmission. The screw passes through one of the pressed retaining pla...

Rear Side Lamp Lens from the rear lamp assembly, for the right-hand side, with clear edge sections. The moulded lens fits over the rear lamp unit,...

Starter Motor for the 2.25L 4-cylinder diesel engine, operating in the engine starting circuit. When energised through the starter solenoid, the p...

Alternator - belt-driven charging unit of the A115 type, rated at 45 amps. Driven from the crankshaft pulley, the alternator carries the vehicle's...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

Crystal Headlamp - a matched pair of 7-inch round crystal halogen headlamps for right-hand-drive applications. The clear (crystal) lens and facete...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

Heated Rear Screen supplied in its frame, for the upper tailgate. The glass carries a printed element grid on its inner face. When the heated rear...

Piston for the 2.25L four-cylinder diesel engine, supplied in an oversize grade for a rebored cylinder block. The piston runs in the cylinder bore...

Trim Drive Fastener for securing interior trim to the body structure. This is a blind, drive-in fastener used where trim must be retained from the...

Wheel Bearing Kit - Metric - Per Wheel

Wheel Bearing Kit for overhauling one wheel hub to imperial specification, front or rear. The hub runs on an inner and an outer bearing, which car...

Universal Joint for the propeller shaft, measuring 75 mm across the bearing caps with a 27 mm cap diameter. Sealed type, supplied without a grease ...

Brake Hose - the flexible hydraulic line in the braking system. It carries pressurised brake fluid from the rigid chassis-mounted brake pipe to the...

Rear Wheel Cylinder for the rear drum brake assembly, left-hand side. Mounted to the brake backplate, the wheel cylinder converts hydraulic pressu...

Rear Wheel Cylinder for the rear drum brake assembly, right-hand side. Mounted to the brake backplate, the wheel cylinder converts hydraulic press...

Conrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...

Mainshaft Bearing for the LT77 five-speed manual gearbox. This tapered roller bearing supports the gearbox mainshaft, locating it within the gearb...

Main Bearing Set for the 2.25L 4-cylinder petrol and diesel engine, supplied in 0.030" oversize. The main bearings are the replaceable shell beari...

Thrust Washer

Main bearing set for the three-bearing 2.25L four-cylinder engine, forming the crankshaft support in the cylinder block bottom end. The shells loc...

Caliper Seal - Rear

Shock Absorber - front suspension damper. Mounts between the chassis bracket and the front axle, controlling the rate at which the coil spring com...

Bonding Lead - earth strap within the chassis wiring harness. Provides a low-resistance earth path between the body and the chassis, maintaining e...

Heated Front Windscreen - front glazing panel with an integral electrical heating element, fitted in place of the unheated screen in the windscreen...