Land Rover Parts

Oil Filter Gasket for the Rover K-Series 1.8L petrol engine, sealing the oil filter housing to the engine block in the lubrication circuit. This g...

Diff oil seal

Water Manifold Gasket for the Puma 2.4L and 2.2L TDCi diesel engine. Seals the coolant water manifold to the cylinder block, maintaining the integr...

Exhaust Manifold Gasket for the 1.8L 4-cylinder K Series petrol engine, sealing the joint between the exhaust manifold and the cylinder head. The ...

Special bolt

Heater Hose - inlet pipe from the cylinder head to the heater matrix, Td5 2.5L 5-Cylinder Turbo Diesel. Carries hot engine coolant from the cylind...

Front Cover Gasket for the LT85 5-speed gearbox front cover joint. It seals the front cover against the gearbox case, retaining oil at the input e...

Outer Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Fan Cowl Flexible Mounting - a rubber mounting for the engine cooling fan cowl. It secures the fan cowl to the radiator, locating the cowl around ...

Camshaft O-Ring for the 2.5L four-cylinder diesel engines, including the naturally aspirated diesel, turbo diesel and 200TDi. This O-ring forms th...

Intercooler to Inlet Manifold Hose for the 300TDi 2.5L turbocharged diesel engine intercooler circuit on the Discovery 1 and Range Rover Classic. ...

Timing Belt Tensioner Washer for 200TDi and 300TDi engines. This slotted packing washer fits to the timing belt tensioner assembly, setting the co...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Oil Filter for the Freelander 1 fitted with the 2.0L L Series Diesel engine. Replaces the engine oil filter as part of a routine oil service. The ...

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...

Inlet Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaft,...

Exhaust Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaf...

Joint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...

Hex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...

Bolt - M12 x 60mm is a metric hexagon head bolt used across a wide range of assembly applications on Land Rover vehicles. Thread specification M12...

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...

Vacuum Pump O-Ring that seals the diesel vacuum pump at its mounting joint. The vacuum pump supplies the depression used by the brake servo on die...

Blanking Plug fills an unused switch aperture in the dashboard switch panel. Where a fascia switch position is not fitted, this plug closes off th...

Locking Washer for the swivel pin housing on the front axle. The washer sits under the swivel pin retaining bolts, and its tab is bent up against t...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Bolt, M10 x 30mm, used to secure the upper mounting bracket of the suspension damper. It fastens the shock absorber upper mount bracket at the fro...

Fuse - 10A for Land Rover electrical systems. This 10A fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Rear Spring Dowel - a locating dowel that positions the rear road spring on its seat. The dowel engages a corresponding hole in the base of the sp...

Anti-Roll Bar Bush for the suspension anti-roll bar (stabiliser bar) mounting. The bush seats around the anti-roll bar and is held to the body by ...

Pop Rivet (blind rivet) used to secure the flexible door rubber, a body and door-trim fixing. The rivet fastens the flexible rubber seal to the do...

Fuel Tank Bolt secures the front mounting of the fuel tank to the chassis, for tanks mounted beneath the front seat. It clamps the tank's forward ...

Shackle Plate for the rear leaf spring shackle assembly, in the extended (long) form used on the heavier-duty chassis. It locates the outer eye of...

Circlip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...

Filler Strip for the door top. The strip fits along the top edge of the door, closing and finishing the joint at the door-top glass frame and seal...

Clevis Pin for the tailboard assembly at the rear of the body. It secures the drop-down tailboard's support cable or chain to its anchor bracket, ...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Threaded 7/16 UNF with a 7/8 in shank length, the bolt clamps the flywhe...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Sac Snap Clip

Oil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Plastic Rivet is a push-fit fastener used to secure interior trim pads, finishers and insulation panels. It retains items such as radio and speake...

Valve Stem Seal fits over the valve guide at the top of the cylinder head on the 2.5L 200 TDi and 300 TDi diesel engines. It wipes and meters lubr...