Products

Radius Arm Bush - Front for the front suspension radius arm assembly. This rubber bush is pressed into the forward end of the front radius arm and...

Fuel Tank Sender Sealing Ring for the fuel tank sender unit assembly. This sealing ring provides the fuel-tight seal between the fuel level sender...

Front Fender - Defender - RH

Fender front Defender LH OEM

Front Wing Panel - Outer, Right-Hand - the exterior body panel enclosing the front wheel arch on the right-hand side. It forms the outer contour o...

Outer left front wing panel forming the exterior body section above the front wheel arch. Designed as a replacement outer wing panel for the left-h...

Radiator Grille Frame - the front-end body component that surrounds and retains the radiator grille panel at the front of the vehicle. It mounts ac...

Body Side Capping - Station Wagon LH is the left-hand external bodyside finisher, a one-piece black moulding that caps the upper edge of the bodysi...

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Front Fender Panel - RH is the right-hand front wing panel, the outer body panel covering the front wheel arch and forming the side of the front bo...

Front Panel - TD5 - LH

Idle Adjusting Needle is the mixture-adjusting needle for the Zenith Stromberg CD175 constant-depression carburettor fitted to the Rover 3.5 V8. I...

Fastener is a fixing used to secure exterior body trim and finisher panels to the bodywork. It retains trim components such as plinths and finishe...

Seat Cushion Cover for the front seat, forming the outer covering over the seat base cushion - the part of the seat you sit on. It replaces a worn,...

Seat Squab Cover for the front seat backrest (squab), forming the outer covering over the backrest cushion. It replaces a worn, torn or faded origi...

Blind Nutsert is an M6 blind rivet nut (rivnut) that provides a captive threaded fixing point. It is set into a single face of sheet metal or pane...

Plain Washer M8

Washer for the non-hinged windscreen frame assembly. It seats on the frame fixings, spreading the fastener clamp load across the mounting surface ...

Flanged Bolt - M8 x 25 mm, Torx drive. Secures the lower body-to-chassis mounting points at the rear of the vehicle. The integral flange spreads c...

Wing Fixing Bolt for the front wing assembly, securing the outer wing panel to the inner wing structure. Clamps the outer wing to the inner wing a...

Fitting Kit for Pacet Fan

Thermostat Kit for Electric Fan Kenlowe

Rock Sliders - bolt-on sill protection bars that run along the lower body between the wheel arches, shielding the sills and lower chassis edge from...

Wing Protector - Long - 3mm Aluminium for the Defender front wings. Aluminium chequer-plate protector that mounts over the front wing tops of the ...

Lamp Guard Set protects the exterior lamp units from impact damage, fitting over each lens to shield it from knocks by branches, debris and shiftin...

Rear Wing Protector - a protective panel fitted over the rear wing to shield the bodywork from scratches, denting and wear during loading and off-r...

Wing Protector is a 3mm aluminium chequer plate that protects the top of the rear wing from scuffs, dents and loading damage. It covers the upper ...

Sill Protector - Aluminium Chequer Plate for the Defender 90. This aluminium chequer plate protector bolts over the door sill to shield it from sc...

Sill Protector Pair - exterior body protection panels that fit along the lower sill (rocker) sections beneath the doors. Supplied as a matched lef...

Brake Hose Kit - non-ABS. A set of flexible brake hoses that connect the rigid brake pipes on the chassis to the moving calipers and rear axle. Th...

Sliding Window Seal Kit - Rear

Seat belt SECURICON

Glass Retainer Kit for the rear safari door window - the aluminium retaining strips that hold the fixed glass in the door frame. The strips clamp ...

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Rear Coil Spring for the rear suspension, raising ride height by approximately 40mm over standard. Wound from 18mm wire with a free height of 445m...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Shock Absorber - a gas-charged front damper for the suspension. Fitted between the front axle and the chassis, it damps the motion of the road spr...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...