Products

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Sealing Washer for the carburettor choke switch on petrol engine applications. Fitted at the choke switch, it seals the joint at the fitting to pr...

Mud Shield for the differential pinion. This pressed shield fits over the differential drive flange, ahead of the pinion oil seal, protecting the ...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Mudshield Output Shaft

Bolt, 7/16" BSF x 1-3/8" secures the upper swivel pin to the swivel housing in the front axle assembly. The top swivel pin retains the swivel ball...

Cone Bearing - Swivel Housing for the front axle swivel pin assembly. Sits within the swivel housing to support the swivel pin on early Series Lan...

Exhaust Bracket for the exhaust system mounting. The bracket secures and locates the exhaust pipework against the underbody, supporting the system...

Spring Road Front SWB 9lf DS

Top Swivel Pin Bearing Spring, part of the front axle swivel pin housing assembly. The spring acts on the top swivel pin bearing to maintain beari...

Seal Ring - a copper crush-type sealing washer. It fits beneath a threaded plug or at a metal-to-metal joint and deforms as it is tightened, takin...

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Oil Pump O-Ring, a seal within the engine oil pump assembly. The O-ring seals the oil pump strainer (pickup) joint, maintaining the suction seal s...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Threaded 7/16 UNF with a 7/8 in shank length, the bolt clamps the flywhe...

Manifold Stud is used to secure the combined inlet/exhaust manifold assembly to the cylinder block on Series vehicles fitted with the 2.25L diesel ...

Rocker Cover Washer used at the rocker (valve) cover fixing on the cylinder head. Fitted beneath the rocker cover retaining nut, the washer seals ...

Cylinder Head Bolt clamps the cylinder head to the cylinder block on the diesel engine, compressing the head gasket to seal the combustion chambers...

Rocker Bush for the rocker shaft assembly in the Defender's 2.5L diesel engine. Fitted to the rocker shaft to support the rocker arms and maintain...

Lock Washer for the starting dog at the front of the crankshaft. The starting dog threads into the nose of the crankshaft to retain the front pull...

Hex Head Bolt with a 1/4" BSF thread and a 5/8" shank length. A common application is the swivel pin housing, where it retains the swivel oil seal...

Nyloc Nut with a 1/2" BSF thread. A nylon insert in the crown of the nut grips the bolt thread as it is tightened, resisting loosening under vibra...

Stud A threaded fastening stud catalogued for use across multiple applications. It is fitted in several locations on the engine and its ancillarie...

Exhaust Manifold Stud for the 3.5L V8 petrol engine, securing the exhaust manifold to the cylinder head. The stud screws into the head and carries...

Screw

Shock Absorber Bolt secures a shock absorber to its mounting in the suspension. The long shank passes through the damper eye and mounting bracket ...

Bolt - 1/2" UNF x 6-1/4", part of the front radius arm chassis mounting. The long shank passes through the radius arm front bush and the chassis m...

Suspension and Chassis Mounting Bolt used across multiple suspension and chassis linkage positions. This hexagon bolt secures components including...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Thrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...

Rocker Cover Gasket (Top) - seals the rocker cover joint on the 2.6L 6-cylinder petrol engine. Fitted between the rocker cover and the cylinder he...

Retainer

Shim is a 0.002" adjustment shim for the manual (non-power-assisted) steering box. It is fitted within the steering box to set the correct end-flo...

Pedal Pivot Bush is the bearing bush on which the clutch or brake pedal pivots within the pedal box assembly. Pressed into the pedal bore, it prov...

Clutch Pedal Box Top Gasket for the clutch pedal housing on manual transmission vehicles. This gasket seals the joint between the clutch pedal box...

Leaf Spring Heavy Duty

Rear Leaf Spring - heavy-duty rear leaf spring for the passenger side, built with eight leaves for increased load capacity. Locates the rear axle ...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Past op  1958 - 61:   Sommige S 3 vanaf 1977 en 110 1983 - 84 All 3 Lug Internal Fixings

Accelerator Pedal Return Spring for the cable-operated throttle linkage. The spring returns the accelerator pedal to its rest position when foot p...

Rocker Bracket Locating Dowel for the cylinder head and rocker assembly in the 2.25L and 2.5L petrol and diesel engines. This dowel locates the ro...

Intermediate Shaft