Products

Cylinder Head Bolt is the short-length head bolt that clamps the cylinder head to the block on the 2.25L and 2.5L 4-cylinder petrol engines. The h...

Bowl Washer is the sealing joint washer for the fuel sediment bowl (sedimentor) in the fuel system. It seals the bowl to its housing, maintaining ...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Lock Washer fitted under a nut or bolt head to lock a threaded fastening against loosening. Its sprung form bears against the joint face and the u...

Hex Nut used in the clutch master cylinder and pipe assembly. This standard hex nut secures hydraulic pipe fittings or mounting hardware within th...

Stekker 7-polig Pvc

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...

Washer

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Chain Bracket Series/Lw

Clevis Pin for the tailboard assembly at the rear of the body. It secures the drop-down tailboard's support cable or chain to its anchor bracket, ...

Plain Flat Washer for use beneath bolt heads or nuts where specified. Used across multiple assemblies including alternator mountings, exhaust manif...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Rope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...

Floor Panel Screw x 100

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Two-Man Bench Seat Cushion for the rear inward-facing bench seat. This is the fixed rear bench cushion that forms the seating surface of the two-s...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Door Hinge Bolt

Door Hinge Spring for the rear door hinge assembly. Return spring fitted within the rear end door hinge on station wagon body variants. Provides t...

Locker Door Hinge

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Aluminium Corner Strip - the curved top retainer for the rear door glass. One of the aluminium retainers in the rear (end) door glazing set, this ...

Corner capping LH S3 galvanised

Rear Body Seal is a rubber seal fitted to the rear body extension panel of the station wagon body. The seal closes the gap between the extension p...

Mounting Plate for the rear door spare wheel carrier assembly. This steel retainer plate secures the spare wheel against the tailgate-mounted spar...

Circlip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Interior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...

Number Plate Lamp Plinth is the mounting base for the rear number plate lamp, fixing the lamp unit to the bodywork above the number plate. It loca...

Heater Control Mounting Plate for the heater control assembly. It provides the fixed mounting that carries the heater control unit, locating the co...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Sill Panel Rear 109 Not Station Wagon - LH