Products

Nutsert, M8 blind rivet nut for use where a permanent threaded insert is required and access to the reverse face of the panel or bracket is not pos...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Tow Hitch - NATO Pintle is a rotating military-pattern towing hook that mounts directly through the rear crossmember. The pintle rotates to allow ...

Clutch Hose forms part of the clutch hydraulic circuit, carrying fluid between the clutch master cylinder and the slave cylinder. The flexible hos...

Exhaust Downpipe is the front downpipe of the exhaust system for the left-hand (LH) cylinder bank of the V8 engine. The downpipe bolts to the LH e...

Spring Washer is a split spring lock washer used at the top of the steering column, at the steering box. Fitted under the securing nut, it maintai...

Front exhaust downpipe, right-hand side, for the V8 exhaust system. The downpipe bolts to the right-hand exhaust manifold flange and carries the e...

Accelerator Cable Dutch Lightweight Diesel

Coolant Hose carries coolant between the radiator and the engine within the cooling circuit. Moulded for the 2.25L carburettor petrol engine fitte...

Exhaust Downpipe - LH - V8 is the left-hand front section of the exhaust system on V8 petrol applications. It connects the left-hand exhaust manif...

Chassis - 109" Station Wagon - Galvanised is a full replacement chassis frame for the long-wheelbase Station Wagon. The galvanised finish provides...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Steering Drag Link - With Bracket - 73cm is a steering linkage rod, supplied with an integrated steering damper bracket. The drag link transmits s...

Galvanised Chassis - complete replacement chassis frame for 88" short-wheelbase vehicles. Fully galvanised as standard, giving corrosion protectio...

Fuel Tank Bolt - shouldered mounting bolt in the fuel tank support assembly, securing the tank mounting to the chassis outrigger. The plain should...

Coolant Hose for the engine cooling circuit of the 2.5L Naturally Aspirated Diesel engine. This hose carries coolant between the engine block and ...

Radiator Bracket - LH is the left-hand mounting bracket that locates and secures the radiator within the engine cooling system. It holds the left-...

Bottom Radiator Hose in the engine cooling circuit, running between the lower hose connector on the engine and the radiator bottom connection. Mou...

Radiator Rubber Mount for the engine cooling system. This rubber mounting locates the radiator in its support panel and cushions it against engine ...

Shock Absorber Bush - Rear Upper is the mounting bush at the upper end of the rear shock absorber, where the damper attaches to its body mounting. ...

PAS Hose - Reservoir to Pump is the low-pressure supply hose in the power-assisted steering hydraulic circuit, running from the fluid reservoir to ...

Fuel Tank Drain Plug - the threaded plug that seals the drain point at the base of the fuel tank. Removing it allows the tank to be drained for se...

Exhaust Downpipe for the right-hand cylinder bank of the V8 engine exhaust system. This downpipe connects the right-hand exhaust manifold outlet t...

Exhaust Clamp Plate for the front exhaust pipe mounting. The plate clamps the front section of the exhaust at its mounting point, holding the pipe...

Lower Strut Gaiter for the rear self-levelling suspension unit. This flexible rubber boot fits over the lower ball joint of the self-levelling str...

Hand Throttle Grommet fits into the hand throttle control assembly, lining the aperture where the throttle cable passes through and sealing it agai...

Bumper Protection Bar - front underside protection bar fitted to the front bumper. The bar mounts beneath the front bumper to shield the underbody...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...

Self Levelling Unit Spring Ring - retaining ring for the rear self-levelling suspension unit. The ring seats on the self-levelling unit and locate...

Fuel Tank Change-Over Tap - manual selector valve for twin fuel tank installations. Mounted on the heelboard, the tap switches the fuel feed betwe...

Joint Steering Upper

Accelerator Cable for the 2.25L diesel engine in left-hand drive Defender 110. This cable connects the accelerator pedal to the throttle control l...

Exhaust U-Bolt secures a section of the exhaust system to its mounting bracket within the exhaust mounting assembly. The U-shaped bolt passes over...

Power Steering Box Bolt - mounting bolt for the power steering box. The bolt secures the Adwest Heavyweight three-bolt power steering box to the c...

Lower Steering Column Universal Joint for the steering column assembly. This universal joint sits at the lower end of the steering shaft, transmitt...

Accelerator Pedal is the driver's throttle input, mounted in the cab footwell against the bulkhead. The pedal pivots on its bracket and operates t...

Clamp bracket lower for steering column shroud

Flexible Brake Hose for the front hydraulic braking circuit. It carries brake fluid pressure between the rigid chassis-mounted brake pipe and the f...