Products

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Bolt - M10 double hex - securing the swivel pin housing to the front axle case. This dowel bolt locates and fastens the swivel pin housing to the ...

Drive Shaft Housing Bolt securing the drive shaft (swivel/stub axle) housing to the axle case. An M10 double-hex (twelve-point) headed bolt used a...

Intermediate shaft lock nut LT230

Drain plug

Plug

Grub Screw for the gearbox and transfer box selector mechanism. This is an M10 grub (set) screw that locks a selector fork or yoke onto its select...

Split Pin is a locking fastener that secures a castellated nut against rotation on steering and suspension linkage joints. Fitted through the dril...

Body Side Steps - a matched pair of fixed side runners for the lower body sides. Mounted along the sill line to the body and chassis fixing points...

Side Steps of fixed twin-tube construction in a black finish, with a ribbed rubber tread along the top face for grip underfoot. Supplied as a pair,...

Mud Flap - a moulded rubber rear mud flap with a ribbed face, hung behind the rear wheel to intercept water, mud and stones thrown up by the tyre. ...

Rubber Floor Mat Set - Front for the front footwells, supplied as a matching pair. The mats are moulded in rubber to protect the front floor area a...

Rubber Floor Mat Set - Front for the front footwells, supplied as a matching pair. The mats are moulded in rubber to protect the front floor area a...

Floor Mat Set - carpet contour mats that lie over the fitted floor covering, shaped to follow the footwell contours so they sit flat and stay in po...

Front Floor Contour Mat Kit is a pair of shaped rubber mats for the front cabin footwells, forming part of the interior floor protection. Each mat...

Front Floor Contour Mat Kit is a pair of shaped rubber mats for the front cabin footwells, forming part of the interior floor protection. Each mat...

Rubber mat set 110 2nd row

Kit - Floor Contour Mat

Front Floor Mat Pair covering the driver and front passenger footwells, supplied as a matched set of two. Shaped to the contour of the front floor...

Front Floor Mat Pair covering the driver and front passenger footwells, supplied as a matched set of two. Shaped to the contour of the front floor...

Floor Mat for the second-row (rear) floor area. It is shaped to fit the rear passenger footwell and protects the vehicle's carpet from mud, moistur...

Floor Mat for the second-row (rear) floor area. It is shaped to fit the rear passenger footwell and protects the vehicle's carpet from mud, moistur...

Multi-Height Tow Bar is a towing assembly for the high-capacity pick-up and crew cab body styles, mounting to the rear of the chassis. The multi-h...

Alloy Wheel - a 7J x 16" five-spoke cast alloy road wheel with a dual (two-tone) finish. The spoke face carries embossed lettering as a styling de...

Front Protection Bar - an A-frame nudge bar for the front exterior protection assembly. The bar is a single-piece construction with a textured bla...

Fuel Return Check Valve is a non-return valve fitted in the fuel return circuit of the Td5 fuel system. It permits fuel flow in one direction only...

Interior Lamp Mounting Bracket in the Defender cabin lighting assembly. This bracket mounts the interior roof lamp to the headlining or roof panel...

double washer, restrictor

Bolt with Washer - M8 x 50 mm bolt supplied with its washer, used as a structural fixing on the body and on engine ancillary mountings. Applicatio...

Door Stud used in the front door assembly, securing the door top frame to the door. The stud passes through the door top frame flange and clamps i...

Washer - M4 flat washer, used to spread the clamping load of an M4 fastener and protect the panel surface beneath the fixing. Fitted at a number o...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Plain washer

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Cam Cover Washer - plain black washer used on the camshaft cover of the Td5 2.5L 5-cylinder turbo diesel engine. It sits under the fixing that ret...

Washer used at front suspension arm pivot points, anti-roll bar stabilizer link connections, and front subframe cross-member fastening interfaces, ...

Washer used at front suspension arm pivot points, anti-roll bar stabilizer link connections, and front subframe cross-member fastening interfaces, ...

Washer 20mm

Restrictor - flat 20 mm plain washer used in the suspension link mountings of the coil-sprung live-axle chassis. It is fitted at the radius arm mo...

Plain Washer is a flat fastening washer fitted under a bolt head or nut to spread the clamping load across a wider area and protect the mating surf...