Products

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Sac Snap Clip

Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Woodruff Key - Camshaft Chainwheel for the 4-cylinder engine timing assembly. This Woodruff key locates the camshaft chainwheel on the camshaft no...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Copper Sealing Washer - a general-purpose copper crush washer used to seal threaded joints, plugs and unions. The soft copper deforms as the fitti...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Suspension Damper

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Oil Pump O-Ring, a seal within the engine oil pump assembly. The O-ring seals the oil pump strainer (pickup) joint, maintaining the suction seal s...

Exhaust Manifold Stud for the 3.5L V8 petrol engine, securing the exhaust manifold to the cylinder head. The stud screws into the head and carries...

Bolt - 1/2" UNF x 6-1/4", part of the front radius arm chassis mounting. The long shank passes through the radius arm front bush and the chassis m...

Suspension and Chassis Mounting Bolt used across multiple suspension and chassis linkage positions. This hexagon bolt secures components including...

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Driving Member Bolt secures the driving member, or drive flange, to the wheel hub. The driving member transmits drive from the axle halfshaft to t...

Brake Caliper Bolt secures the rear brake caliper to its mounting bracket within the rear braking assembly. It clamps the caliper body in position...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Hex Nut used in the clutch master cylinder and pipe assembly. This standard hex nut secures hydraulic pipe fittings or mounting hardware within th...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Plain Flat Washer for use beneath bolt heads or nuts where specified. Used across multiple assemblies including alternator mountings, exhaust manif...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Striker Plate

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Lock Barrel Set - 3 Barrels & Keys for anti-burst door locks in the door locking assembly. This set supplies three matching lock barrels and k...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...