Products

Swivel Housing Kit providing a complete overhaul of the front axle swivel assembly for one side, supplied complete with the swivel housing ball. T...

Timing Kit - 2.0L T16 Petrol

Major Service Kit for the 200 TDi 2.5L four-cylinder turbo diesel, grouping the scheduled lubrication, induction and fuel filtration items into a s...

Major Service Kit for the 200 TDi 2.5L four-cylinder turbo diesel, grouping the scheduled lubrication, induction and fuel filtration items into a s...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Service Kit for the 3.9L V8 EFI petrol engine, grouping the scheduled lubrication, induction and fuel filtration items into a single pack. The kit...

Screw used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...

Goodridge Brake Hose Kit - +2"

Rear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...

Rear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...

Rear Brake Caliper for the left-hand side of the rear axle, part of the hydraulic braking circuit. The caliper carries the hydraulic pistons that ...

Rear Brake Caliper for the left-hand side of the rear axle, part of the hydraulic braking circuit. The caliper carries the hydraulic pistons that ...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Hex Socket Screw, M8 x 20 - hexagon socket head fixing screw. Used on diesel engine installations at points where a conventional hexagon head cann...

Bolt – a threaded fixing used to secure engine ancillary components at several mounting points, depending on application. Typical positions includ...

Plenum Chamber Screw – a threaded fixing for the plenum chamber on the V8 EFI petrol induction system. The screw secures the plenum chamber to the...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Bolt 7/16" UNF × 3/4" for securing the drive plate spacer to the crankshaft flange on the Rover V8 engine with automatic transmission. In automati...

Piston Assembly for the 2.5L 200 TDi turbo diesel, forming part of the piston and connecting-rod assembly within the cylinder block. The piston tr...

Sealing Washer - sump plug sealing washer for the ZF four-speed automatic gearbox. Fitted under the head of the transmission sump drain plug, the ...

Gear Selector Kit for the manual gearbox, covering the internal gear-selection mechanism that engages and disengages the gear ratios. The selector...

Rear Body Crossmember is a structural member of the rear floor assembly. It spans the rear of the body floor, tying the floor pan and the rear end...

Intake Air Valve Assembly is the rubber dust valve fitted to the base of the air cleaner housing in the engine air intake system. This one-way fla...

Inlet Valve for the cylinder head valvetrain of the 3.5 V8 carburettor petrol engine. The inlet valve seals the intake port against combustion pre...

Exhaust Valve for the cylinder head valvetrain of the 3.5 V8 petrol engine. The exhaust valve opens to release burnt gases into the exhaust port a...

Repair kit for clutch master cylinder, fits to AEU1714, ANR2651.

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Cylinder Head Gasket Set for the 2.5L 200TDi turbo diesel engine, supplying the top-end gaskets and seals required when the cylinder head is remove...

Set - 200 TDi Head Including Bolts

decoke gasket set cylinder head 200TDi engines, WITHOUT head gasket. OEM Elring quality.

Seat Belt Fixing Kit provides the mounting hardware used to secure a seat belt assembly to the vehicle body anchorage points. The kit supplies the...

Distributor Module for the 3.5L Rover V8 petrol engine, used with the earlier single-coil electronic ignition system. It forms part of the distribu...

Ignition Module & Link Lead - a kit for the 3.5L Rover V8 petrol engine ignition system, comprising the electronic ignition module (amplifier) ...

Ignition Module Link Plug - a 3-to-2 pin adapter plug used with the V8 distributor ignition module. It adapts the wiring connection between a 3-pi...

Vacuum Advance Unit for the ignition distributor on V8 EFI petrol engines, for distributors fitted with a three-pin amplifier module. The vacuum c...

Fuel Pump Kit for the mechanical diesel lift pump in the low-pressure fuel supply circuit of 2.5L naturally aspirated diesel, 2.5L turbo diesel and...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Distributor Lead for the ignition system of the 3.5L V8 petrol engine. This lead connects the distributor to the ignition amplifier module, adapti...

Headlamp Fixing Kit for headlamps with manual beam adjustment. The kit renews the fixings and adjusters that retain the headlamp unit and set its ...

Headlamp assy LHD RH OEM MAGNETI MARELLI

Headlamp Bulb Cover for the front headlamp assembly. This rubber cover seals the bulb access aperture at the rear of the headlamp unit following b...