Products

Air Suspension Line - Compressor - 500 mm is a 500 mm service length of air suspension pipe used in the compressor circuit of the electronic four c...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Air Suspension Transfer Relief Valve - solenoid valve in the air suspension compressor and supply circuit, mounted at the supply reservoir. Contro...

Transfer Relief Valve - Front Axle in the electronic air suspension system. Fitted in the front axle branch of the air suspension pneumatic circui...

Eccentric Washer - an adjusting washer used at the front suspension arm pivot mounting. The offset (eccentric) hole allows the arm's pivot bolt po...

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...

Bolt Mounting bolt for the front suspension arm. Part of the front suspension assembly, it secures a front upper or lower control arm (wishbone) a...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Bolt for the rear suspension assembly. This fastener is used in the rear cross member and stabilizer bar assembly, and in the rear knuckle and low...

Special Nut - secures the rear knuckle to the lower and upper suspension arms. It retains the rear suspension arm bolts at the knuckle, holding th...

Adjusting Nut is an M17 flanged nut used in the rear suspension toe link assembly. It locks the toe link adjuster at its connection to the rear kn...

Nut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...

Nut

Flanged Nut M16 flanged nut for the rear suspension arm fixings. Part of the rear multi-link suspension assembly, it secures the lower and upper s...

Screw - an M6 x 20 mm pan-head setscrew with a Torx drive, used as a general multi-application fastener. The Torx socket gives positive tool engag...

Trim Clip - push-type retainer used to secure exterior trim, body mouldings, bumper covers and splash shields to the body structure. The clip is p...

Circlip for the lower steering knuckle bush. This circlip retains the bush within the lower steering knuckle, forming part of the front axle and s...

Brake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...

Disc - Brake

Disc - Brake

Brake Pad Wear Sensor - front brake pad wear warning wire, part of the front disc brake friction-monitoring circuit. The sensor wire clips into th...

Parking Brake Shoe Fitting Kit for the drum-in-hat parking brake housed within the rear brake discs. The kit supplies the retaining pins and clips...

Brake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...

Parking Brake Cable Bracket from the parking brake cable routing. The bracket anchors the cable outer casing at a fixed point on the vehicle, so th...

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Grommet for the inspection aperture in the rear brake backplate. The backplate carries an access hole through which the parking brake shoe adjuster...

Handbrake Actuating Pawl Rod Actuating rod within the rear parking brake mechanism of the drum-in-disc handbrake assembly. It transmits handbrake ...

Parking Brake Adjuster Kit for the rear parking brake (drum-in-disc) mechanism. The kit renews the adjuster components that set the clearance betw...

Brake Disc Bolt - M10 x 20mm securing the brake disc to the hub flange. M10 x 20mm bolt with 1.5mm thread pitch. Multiple bolts are required per d...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

Kit - Boot

Axle oil filler plug, sealing the combined fill and level aperture in the axle casing. Used at both front and rear axle positions. The plug closes...

Spring Washer used in the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It is fitted under the fastener securing th...

Washer - Sealing

Bolt for the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It secures the gear change mechanism to its mounting on ...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Automatic Transmission Fluid for ZF 6HP Series Transmissions, supplied in a 1-litre bottle. This fluid is formulated from a blend of hydrocracked ...

Rear Output Shaft Oil Seal for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It seals the point where the output shaft leaves the rear ...