Products

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Suspension Damper

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

LED Festoon Bulb for interior lamps. A double-ended festoon LED that replaces the standard filament festoon bulb in the courtesy, map and interior...

Gearbox Oil 75W80 is a 75W80-grade manual transmission fluid (MTF) formulated for the R380 5-speed manual gearbox. It lubricates the gears, synchr...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Hex Nut is an M8 copper flanged-head nut used on the exhaust manifold. The flanged head spreads the clamping load and removes the need for a separ...

Front Brake Hose - flexible hose in the front hydraulic brake circuit, connecting the rigid brake pipe on the body to the front brake caliper. Rei...

Water Pump Gasket

EGR Valve Control - vacuum control valve in the exhaust gas recirculation (EGR) system. Regulates the vacuum signal that operates the EGR valve, c...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Screw for use in Land Rover body, chassis, and hardware applications.

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Insulation Pad Clip A fir-tree style retaining clip that holds the under-bonnet sound-deadening and heat insulation pad in place. The clip pushes ...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Locking Fuel Filler Cap Assembly. It seals the fuel filler neck and locks to secure the filler against unauthorised access. Supplied to a non-speci...

Front Door Lock (Latch) Assembly for the left-hand door on left-hand-drive applications, part of the door body fittings and central-locking system....

Wiper Spindle Cap - outer cap for the windscreen wiper spindle, installed at the outer end of the spindle where it passes through the scuttle panel...

Wiper Spindle Washer for the rear screen wiper assembly. This plastic outer washer fits over the wiper spindle where it exits the body panel, seati...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Wheel Centre Trim Cover for steel road wheels. This black plastic cap fits into the centre of each steel road wheel, covering the wheel fixings an...

Bolt - M12 x 115 for the suspension and chassis assembly of the Freelander 1. Used in radius arm, subframe, and towing equipment mountings, where ...

Power Steering Pump is the engine-driven hydraulic pump at the heart of the power steering circuit. Driven by the engine accessory belt, it draws ...

Wheel Hub Bearing for the front and rear wheel hub assemblies. The bearing locates the hub on the stub axle and steering knuckle, carrying the veh...

Front Wing Assembly - Left Hand is the outer body panel covering the front wheel arch on the left-hand side of the vehicle. It forms the front-lef...

Ignition Lead Set for the 1.8L K Series four-cylinder petrol engine - the high-tension (HT) leads that carry the ignition voltage from the coil to ...

Air Conditioning Compressor for the refrigerant circuit on 2.0L diesel applications fitted with air conditioning. Belt-driven from the engine, the...

Wiper Blade for the rear screen wash/wipe system. Fits the rear wiper arm and sweeps the tailgate glass, operating with the rear wiper motor and w...

Gear Lever Gaiter for the manual transmission gear shift assembly. It fits over the base of the gear lever where it passes through the transmission...

Air Conditioning Condenser - part of the air conditioning refrigerant circuit, mounted at the front of the vehicle in the airflow path ahead of the...

Flanged Bolt - M8 x 25 mm, Torx drive. Secures the lower body-to-chassis mounting points at the rear of the vehicle. The integral flange spreads c...

Locking Wheel Nut Set secures the road wheels against theft, fitting in place of the standard wheel nuts on the hub studs. Each nut carries a uniq...

Anti-Roll Bar Kit is a complete front and rear anti-roll bar upgrade for the suspension. It replaces the standard front anti-roll bar with a thick...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...