Products

Flanged Screw - threaded fastener with an integral flange head that spreads the clamping load, used in vehicle assembly.

Needle Roller Bearing - 3rd Gear Mainshaft is installed within the LT77 5-speed manual gearbox mainshaft gear assembly, supporting the 3rd gear on ...

ABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...

ABS Sensor Seal for the anti-lock braking system. The seal fits at the ABS sensor location, sealing the sensor bore against fluid and contaminatio...

Pinion Shaft is the mainshaft of the LT77 five-speed manual gearbox, running through the gear cluster to carry the driven gears and transmit drive ...

Gearbox Mainshaft is the central output shaft of the LT77 5-speed manual gearbox, running the full length of the transmission from the input end to...

Front Hub for the front wheel hub assembly. The hub mounts on the stub axle, houses the wheel bearings and carries the road wheel, with the brake d...

Beck B Plate Clutch

Clutch Plate

Shaft coupling

Synchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Front Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Layshaft Bearing is the layshaft taper roller bearing for the LT77 and R380 5-speed manual gearbox. Located in the gearbox centre plate, it suppor...

Fitment: All models (VIN) LA930456 on

Hub assembly front RH includes bearing P38

Selector Fork for the 5-speed manual gearbox internal gear-change mechanism. The selector fork engages with the synchromesh hub sleeve to move the...

Crown Wheel Bolt secures the crown wheel (ring gear) to the differential carrier within the axle differential. Threaded 3/8 UNF and 1.1/8 inch lon...

Hexagonal Plug for the swivel pin housing oil level and drain. This hex-head plug is used in the front axle swivel pin housing as both an oil leve...

Rear Propeller Shaft for the rear driveline. The propeller shaft transmits drive from the transfer box rear output flange to the rear axle differe...

Clutch Slave Cylinder Push Rod transmits movement from the hydraulic slave cylinder to the clutch release lever. As the slave cylinder extends, th...

Gasket

Propshaft Bolt, M12 x 65 mm, property class 10.9. The bolt secures the rear propshaft to its rubber coupling (the flexible drive coupling at the pr...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 5th gear selector bias. It works within the gear lever remote housing...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

External Circlip for the R380 manual gearbox selector yoke. The circlip locates in the groove on the selector yoke and retains it in position with...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Mudshield

5th Speed Countershaft Gear for the R380 5-speed manual gearbox in V8 petrol applications. This is the countershaft (layshaft) member of the fifth...