Products

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Front Floor Crossmember for the body floor structure on the Discovery 1 and Range Rover Classic. This crossmember spans the width of the floor pan...

Headlamp Adjuster for the manual headlamp levelling system, fitted to the headlamp unit. It sets the vertical aim of the headlamp beam, allowing t...

Programmable Wiper Delay Relay is a direct replacement for the standard AMR2341 relay in the front wiper circuit, providing a user-adjustable inter...

Headlamp Assembly for the front lighting system, halogen type without headlamp levelling. The complete unit houses the main and dipped beam reflec...

Headlamp Assembly for the front lighting system, halogen type. The complete unit houses the main and dipped beam reflector and lens and mounts int...

Headlamp Assembly is a complete halogen front headlamp unit within the exterior lighting system, supplied with its integral manual levelling mechan...

Headlamp Kit

Headlamp Kit

Reverse Light Switch for the R380 5-speed manual gearbox, completing the reverse lamp circuit when reverse gear is engaged. This switch threads in...

Wiper Spindle Washer for the rear screen wiper assembly. This plastic outer washer fits over the wiper spindle where it exits the body panel, seati...

Alternator 300TDi (with pulley)

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Power Steering Pump is the engine-driven hydraulic pump at the heart of the power-assisted steering circuit on the 300 TDi 2.5L turbo diesel. Belt...

Clutch Master Cylinder for the clutch hydraulic circuit, installed at the pedal box. The cylinder converts mechanical clutch-pedal movement into h...

Brake Valve for the front brake hydraulic circuit. Regulates hydraulic pressure to the front brakes and is used on both ABS and non-ABS systems.

Brake Valve for the front brake hydraulic circuit. Regulates hydraulic pressure to the front brakes and is used on both ABS and non-ABS systems.

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Road Spring is a coil spring located at the suspension bottom link. It carries the vehicle load and maintains ride height, absorbing road inputs t...

Rubber Mount is an axle assembly mounting bush. It isolates the axle-mounted assembly from the surrounding structure, absorbing vibration and cush...

Air Suspension Compressor Assembly supplies pressurised air to the Electronic Air Suspension (EAS) system, inflating the air springs to raise the v...

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

Fuel Tank Sender Sealing Ring for the fuel tank sender unit assembly. This sealing ring provides the fuel-tight seal between the fuel level sender...

Idle Adjusting Needle is the mixture-adjusting needle for the Zenith Stromberg CD175 constant-depression carburettor fitted to the Rover 3.5 V8. I...

Glovebox Damper is the damper assembly for the glovebox lid. It controls the opening motion of the glovebox, slowing the lid as it drops so it low...

Plain Washer M8

Fitting Kit for Pacet Fan

Thermostat Kit for Electric Fan Kenlowe

Dog Guard Kit installs behind the rear seats to separate the load area from the passenger cabin, keeping pets and shifting luggage out of the occup...

Steering Wheel Boss - the mounting hub that adapts an aftermarket steering wheel to the steering column splines. Compatible with the BA 150 and BA...

Seat belt SECURICON

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Rear Coil Spring for the rear suspension, raising ride height by approximately 40mm over standard. Wound from 18mm wire with a free height of 445m...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Brake Hose Kit - Stainless Steel

Shock Absorber - Rear - Gas

Shock Absorber - a gas-charged front damper for the suspension. Fitted between the front axle and the chassis, it damps the motion of the road spr...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...

Raised Air Intake Mantec - 90/110 200TDi

Front Twin Shock Tower (Pair) - an uprated front shock absorber mounting set for coil-sprung suspension that allows a second shock absorber to be f...

Front Spring - +50mm - Off-Road - Pair is a pair of front coil springs for the front suspension, wound to a raised free length that lifts the front...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...