for Discounts / VAT
for Discounts & Correct VAT
Fuel Injector Pipe is a rigid high-pressure line in the common-rail fuel injection system, forming part of the fuel injectors and pipes assembly on...
View full detailsFuel Balance Pipe for the 3.0L V6 diesel engine, part of the fuel injectors and pipes group within the engine fuel system. The pipe runs across th...
View full detailsIdler Pulley is a guide pulley in the auxiliary (accessory) drive belt system of the 2.7L and 3.0L TDV6 diesel engine. Mounted at the front of the...
View full detailsIdler Pulley is a guide pulley in the auxiliary (accessory) drive belt system of the 2.7L and 3.0L TDV6 diesel engine. Mounted at the front of the...
View full detailsOil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...
View full detailsOil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...
View full detailsLambda Sensor - right-hand bank exhaust gas oxygen sensor for the 5.0L AJ133 V8 petrol engine, mounted in the front pipe and catalyst section of th...
View full detailsLambda Sensor - right-hand bank exhaust gas oxygen sensor for the 5.0L AJ133 V8 petrol engine, mounted in the front pipe and catalyst section of th...
View full detailsLambda Sensor - left-hand bank exhaust gas oxygen sensor for the 5.0L AJ133 V8 petrol engine, mounted in the front pipe and catalyst section of the...
View full detailsLambda Sensor - left-hand bank exhaust gas oxygen sensor for the 5.0L AJ133 V8 petrol engine, mounted in the front pipe and catalyst section of the...
View full detailsAuxiliary Drive Belt is the front accessory drive belt for the 2.7L and 3.0L V6 turbo diesel engine. It transfers drive from the crankshaft pulley...
View full detailsTransmission Oil Cooler from the automatic transmission cooling circuit. Installed in the front cooling pack, it receives hot fluid from the gearbo...
View full detailsTriple Brake Pipe Clip from the brake pipe routing hardware. It retains three rigid brake pipes side by side in one mounting, holding them at a fix...
View full detailsControl Cable Bracket locates and secures a control cable along its routing, fitted to the left-hand side. It anchors the cable run at a fixed poi...
View full detailsFront Bumper Reinforcement is the structural crossbeam that forms the load-bearing armature of the front bumper assembly. It mounts across the fro...
View full detailsHose filler neck
Compressor Assembly
Power Steering Pump for the 3.0L supercharged V6 and 5.0L V8 (AJ133) petrol engines, forming the pressure source of the hydraulic power steering ci...
View full detailsHeadlamp Washer Non-Return Valve fitted in the headlamp washer fluid circuit, in the delivery line between the washer pump and the headlamp jet noz...
View full detailsBody blanking plug 12 X 18MM
Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...
View full detailsCharge Air Pressure Sensor measuring the pressure of the compressed intake charge at the secondary compressor outlet, within the intercooler, air d...
View full detailsRepair Master Cylinder Kit
Brake Booster Kit supplying the vacuum brake servo that sits between the brake pedal pushrod and the master cylinder in the braking hydraulic circu...
View full detailsExterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...
View full detailsBolt, M8 x 1.25 for the front end carrier assembly. This threaded fastener secures components within the front end carrier, which supports the fro...
View full detailsFront Seat Adjuster Switch for the non-memory power seat, in right-hand drive configuration. Part of the electric seat-adjustment system. Mounted ...
View full detailsExhaust Gas Temperature Sensor - middle-position sensor in the exhaust after-treatment system. It reports exhaust gas temperature at its point in ...
View full detailsExhaust Gas Temperature Sensor for the front position in the exhaust front pipe and catalyst assembly. The sensor threads into the front pipe upst...
View full detailsBrake Pad Set for the rear axle, with a ceramic friction compound. The pads locate in the rear caliper carrier and clamp against the rear brake di...
View full detailsBrake Caliper Seal Kit for the rear brake calipers - one kit is required per caliper. The kit renews the internal seals and dust boots inside the ...
View full detailsBleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...
View full detailsRadiator Assembly - the primary coolant-to-air heat exchanger of the engine cooling system, mounted in the front cooling pack. Hot coolant leaving...
View full detailsRadiator Assembly - the primary coolant-to-air heat exchanger of the engine cooling system, mounted in the front cooling pack. Hot coolant leaving...
View full detailsBrake Pad Fitting Kit - Front - caliper hardware set used when renewing the front brake pads, covering the guide bush and seal components that loca...
View full detailsIntercooler - the charge-air cooler of the turbocharger induction system, mounted in the front cooling pack where it receives ram airflow. Air lea...
View full detailsSpacer for the cooling system, used at the mounting of the radiator and coolant overflow container. The spacer sets the correct standoff at the mo...
View full detailsDrive Belt Tensioner for the auxiliary drive belt on the 2.7L and 3.0L TDV6 diesel engines. The spring-loaded tensioner maintains correct tension ...
View full detailsFront Brake Disc, internally vented, for the front braking system. The disc mounts to the front hub and provides the friction surface acted on by ...
View full detailsBrake Disc - rear axle, internally vented, for the 5.0L supercharged V8 petrol (AJ133) installation. The disc provides the friction surface that t...
View full detailsBrake Disc - rear axle, internally vented, for the 5.0L supercharged V8 petrol (AJ133) installation. The disc provides the friction surface that t...
View full detailsJumper Wire Assembly - rear bumper wiring link in the body electrical system, for vehicles equipped with the rear parking aid. It bridges the rear...
View full detailsFront Air Spring - the air bag element of the front suspension strut in the electronic air suspension (EAS) system. It mounts over the front dampe...
View full detailsFront Air Spring - the air bag element of the front suspension strut in the electronic air suspension (EAS) system. It mounts over the front dampe...
View full detailsRear Air Spring - the air bag element of the rear air suspension, used on both four-corner air suspension and front-coil/rear-air self-levelling sy...
View full detailsRear Air Spring - the air bag element of the rear air suspension, used on both four-corner air suspension and front-coil/rear-air self-levelling sy...
View full detailsDamper Seal Kit - service kit for renewing the seals within the air spring assembly, covering both the front suspension struts and the rear shock a...
View full detailsDamper Seal Kit - service kit for renewing the seals within the air spring assembly, covering both the front suspension struts and the rear shock a...
View full details