Products

Striker Plate

Bullet Connector, single-sleeve, one-way. Accepts a standard bullet terminal and is used throughout Land Rover wiring harnesses for individual wire...

Bush GENUINE LR sold EACH! for fitting air intake grille 90/110/130 and for fitting old type individual letters "Range Rover"

Selector Detent Spring is part of the gearbox gear-selection detent for the forward-gear selector shafts (1st/2nd and 3rd/4th). It loads the deten...

Flywheel Housing Stud secures the flywheel housing to the rear of the cylinder block on the 2.0L petrol engine. The stud provides a threaded fixin...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Air Suspension Compressor for the electronic air suspension system, supplying pressurised air to the system's air springs. It draws and compresses...

Steel Ball, a precision steel ball used within the engine oil pump assembly of the lubrication system. It seats inside the oil pump body as a comp...

Wiper Motor Shaft & Gear is the internal drive shaft and gear for the central windscreen wiper motor, providing a 120-degree sweep. It transmi...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Diff Cage Bearing

Tank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Screw Cap Seal 2.0 & 2.5 Coilover (08 18

Cushion Rubber Guide Rod 2.5 Coilover (0

Coilover Guide Rod Bush, a rubber bush sized for a 2.0 in coilover guide rod. It locates and cushions the guide rod within the coilover damper ass...

Door Control Unit - 2-Door

Coilover O-Ring seals the floating end cap of a 2.0-inch coilover damper. Fitted between the end cap and the damper body bore, the O-ring retains ...

Coilover O-Ring seals the floating end cap of a 2.5-inch coilover damper. Fitted between the end cap and the damper body bore, the O-ring retains ...

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Door Hinge Bolt A fixing screw for the front door hinge, part of the door hinge mounting hardware. It secures the hinge to the body pillar and doo...

Mounting Angle is the left-hand front bracket within the front wing and deck panel assembly. The angle bracket locates and supports the front wing...

Mounting Angle is a front bracket within the front wing and deck panel assembly. The angle bracket locates and supports the front wing and deck pa...

Door Lock Assembly - RH for the Range Rover Classic 2-Door Station Wagon. Fitted to the right-hand door, this lock unit provides the latching and ...

Roll Pin for Door Hinge on the Range Rover Classic. A small cylindrical spring pin that locates and retains components within the door hinge assem...

Tailgate Seal - the weather seal for the upper tailgate, part of the rear body closure assembly. Fitted around the upper tailgate aperture, it for...

Tailgate Seal - the weather seal for the upper tailgate, part of the rear body closure assembly. Fitted around the upper tailgate aperture, it for...

Upper Tailgate Lock Barrel & Key secures the upper tailgate (load door) and provides key-operated locking. Supplied as the lock barrel with it...

Front Door Hinge Set Screw secures the front door hinge to the body pillar and door within the door mounting hardware. It clamps the hinge leaf in...

Edge Clip A black edge clip with a delta-section profile that grips a panel flange. It provides a push-on fixing along the edge of the door assemb...

Lock Barrel Set - 3 Barrels & Keys for anti-burst door locks in the door locking assembly. This set supplies three matching lock barrels and k...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Heater Control Finger Grip The finger grip fitted to the hot/cold (temperature) control on the heater control panel. It clips onto the control lev...

Door Seal The lower front door seal for the right-hand door, sealing between the front door and the bulkhead. It forms the weather seal along the ...