Products

Gearbox Mainshaft Washer - the washer that sits in the retaining-nut stack at the rear of the gearbox mainshaft, seating beneath the mainshaft lock...

Cylinder Head Shroud - the injector shroud fitted into the cylinder head of the 2.25L diesel engine. It seats in the head around the injector, shi...

Locating Screw for the engine. A locating screw sets and holds the position of a component against its mounting during assembly. Applies to the 2....

Bolt with a 5/16" UNF thread and a shank length of 2-3/4 inches. A standard-thread fastener used in assembly of the four-cylinder engine. Applies ...

Crankshaft - 3-Bearing

Thrust Washer for the upper swivel pin Railko bush, part of the front axle steering swivel assembly. The Railko bush forms the upper pivot bearing...

Layshaft (countershaft) for the manual gearbox, specific to the Suffix B and C gearbox builds. The layshaft carries the constant-mesh cluster gear...

Layshaft Distance Piece - 0.445in is a precision spacer fitted to the layshaft in the manual gearbox of Series IIA and Series III Land Rovers. The...

Sump - 2.25 Petrol/Diesel - 2.5 Petrol is the engine oil sump (oil pan) for the 2.25L 4-cylinder petrol, 2.25L 4-cylinder diesel, and 2.5L 4-cylind...

Hex Nut - an M10 hexagon nut manufactured to property class 8. A general-purpose threaded fastener that clamps onto an M10 male thread; the class ...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Spring Washer - an M10 single-coil spring lock washer. Fitted under a nut or bolt head on M10 fasteners, it applies axial tension to help resist l...

Spring Washer sized for M16 fasteners. Fitted under the nut or bolt head, the split spring washer exerts a constant axial load against the joint a...

Fuel Pipe Olive

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Exhaust Rocker Arm - 2.6L - LH operates an exhaust valve in the valvetrain of the 2.6L straight-six petrol engine. Mounted on the rocker shaft, it...

Alternator Belt for the 2.5L four-cylinder petrol engine. This drive belt runs from the crankshaft pulley to the alternator, turning the alternator...

O-Ring for use in two distinct applications on classic Land Rover engines. On the Series IIA 2.6L 6-cylinder engine, this O-ring seals the cylinde...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Speedo cable oil seal retainer plate

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Lower Steering Drop Arm for the steering relay assembly. This is the lower lever that clamps to the bottom of the steering relay shaft. Within the...

Piston, 0.040in Oversize for the cylinder block assembly of the 2.6L 6-cylinder petrol engine. The piston runs in the cylinder bore and transmits ...

Brake Pipe for the front braking hydraulic circuit. This is the flexible pipe that feeds the front wheel cylinders. It connects the chassis-mounte...

Shackle Plate for the rear leaf spring shackle assembly, in the extended (long) form used on the heavier-duty chassis. It locates the outer eye of...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Differential Spindle

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Swivel pin housing Series

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Spire Nut is a spring-steel push-on clip fastener that provides a threaded anchor in thin sheet metal. The nut pushes over a hole in a panel and r...

Worm Speedo

Steering Universal Joint for the steering column, transmitting rotation through the angled coupling between the column shaft and the steering box i...

Crankshaft Front Key locates and locks the timing sprocket or front pulley hub to the crankshaft snout, preventing rotational slip between the cran...