Products

Plain Washer (M10) for use at the fuel tank mounting points on Series, Defender, and Range Rover Classic vehicles. Fitted beneath the mounting bol...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Piston Ring Set for the 2.5 litre four-cylinder naturally aspirated diesel engine, standard bore size. The rings seal the combustion chamber again...

Locking Wheel Nut Kit - Spare Wheel

Gasket inlet manifold Td4 Reinz

Intake Gasket

Hex Nut is an M8 copper flanged-head nut used on the exhaust manifold. The flanged head spreads the clamping load and removes the need for a separ...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Front Brake Hose - flexible hose in the front hydraulic brake circuit, connecting the rigid brake pipe on the body to the front brake caliper. Rei...

Clutch Driven Plate (friction disc) for the clutch assembly, 9 1/2 inch diameter. The driven plate is clamped between the flywheel and the pressur...

Water Pump Gasket

Camshaft Position Sensor Assembly for the 4.4L V8 petrol engine management system. The sensor mounts at the timing gear cover and reads the positio...

Clutch Plate

Clutch Plate

Clutch Plate

Clutch Driven Plate - the friction disc of the clutch, splined to the gearbox input shaft and clamped between the flywheel and the clutch cover. I...

Clutch Kit 3.9V8 AP

Water Pump for the 4.4L V8 petrol engine, forming part of the coolant circulation circuit. Driven by the accessory drive belt, the pump circulates...

Turbocharger Gasket

Rocker Cover Gasket sealing the valve rocker cover to the cylinder head. It seals the top of the cylinder head, containing oil around the valvetra...

V-Belt - a drive belt within the engine's auxiliary (accessory) drive, running from the crankshaft pulley to transmit rotational drive to belt-driv...

EGR Valve Control - vacuum control valve in the exhaust gas recirculation (EGR) system. Regulates the vacuum signal that operates the EGR valve, c...

Brake Caliper Seal Kit for the rear 2-piston brake caliper, part of the rear hydraulic braking circuit. The kit renews the caliper's hydraulic sea...

Drive Belt

Rear MQB Asm Shock Tt Tts - Series 3

Bulb - HB4 (9006) - a single-filament halogen headlamp bulb with a P22d base, rated 12V 51W. The HB4 type serves low-beam, high-beam or front fog ...

Inlet manifold stud

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Halfshaft Collar is a locating collar fitted to the front axle halfshaft. It seats against the inner side of the halfshaft bearing (244150), setti...

Gearbox Thrust Washer

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Starter Motor for the 2.25L petrol engine, 24V system - part of the engine starting circuit. On cranking, the motor's pinion engages the flywheel ...