Products

Water Pump for the engine cooling system, driving coolant circulation through the engine and radiator. The pump is belt-driven from the front of t...

Water Pump for the engine cooling system, driving coolant circulation through the engine and radiator. The pump is belt-driven from the front of t...

Breather Valve - Crankcase Vent is the crankcase breather (PCV) valve in the breather system of the 3.5 and 4.2L V8 petrol engine. It regulates bl...

Sump Gasket seals the oil sump to the underside of the cylinder block on the 3.5 and 4.2L V8 petrol engine. It forms the oil-tight joint between t...

Thermostat Cover forms the coolant outlet housing on the 4.0 and 4.2L V8 petrol engine (naturally aspirated). It encloses the thermostat at the en...

Rear Crankshaft Oil Seal for the 3.0L V6 petrol engine (JV6). It seals the rear of the crankshaft where it exits the cylinder block behind the flyw...

Cylinder Head Bolt for the V8 petrol engines (AJ33, AJ40 and AJ133, 4.2L and 5.0L). It clamps the cylinder head to the block, compressing the head ...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Spire Nut - No. 10 U-Type for use in dashboard and body panel fixings on Land Rover Defender and Discovery I. This U-type spire nut clips onto she...

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Spire Nut is a spring-steel sheet-metal fastener that clips over a panel edge or into a pierced hole to provide a threaded anchor point. The arche...

Side Trim Panel is an interior body trim panel that lines and finishes the right-hand side of the 90" wheelbase bodyshell. It conceals the inner bo...

Rear Lower Body Side Panel - an exterior bodywork panel forming the lower rear section of the side body structure. It provides the outer skin below...

Rear Wheelarch Eyebrow Moulding - Unpainted for the Defender body exterior. This moulding fits over the rear wheelarch aperture, covering the body...

Wheel Arch Moulding – Rear An eyebrow trim moulding fitted to the rear wheel arch lip. It follows the curve of the wheel arch flange, covering the...

Eyebrow Moulding

Upper Tailgate Gas Support Strut for the rear tailgate assembly. The strut supports the upper tailgate in the raised position, holding it open whil...

Front Wing for the right-hand side of the body. The wing is the outer body panel that encloses the front wheel arch, spanning from the A-pillar and...

Outer Sill for the left-hand side of a five-door body. The sill is the structural body panel that runs along the base of the door apertures between...

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Support Bracket is a body-side mounting bracket within the door assembly. It provides a fixing point on the door structure, supporting the attachm...

Door Latch Adjuster. Part of the door latch mechanism, it sets the striker engagement so the door aligns, closes and seals correctly. It serves the...

Door Glass for the front door, left-hand side, in clear (un-tinted) glass. This is the sliding window pane that runs in the door channels and is ra...

Door Glass for the front door, right-hand side, in clear glass. This is the main glass panel for the front door, forming part of the door glazing ...

Body Seal seals the joint between the rear upper body panel and the lower body section.

Rear Upper Waist Seal. It seals along the upper waist line of the rear body, closing the joint between the body side and the glass line to keep out...

Bonnet Gas Strut. This gas-filled support strut holds the bonnet open and controls its rise and fall, carrying the weight of the panel throughout i...

Front Outer Wing - Aluminium - LH for the Defender outer body panel assembly. This left-hand front outer wing is manufactured in aluminium and doe...

Front Outer Wing for the right-hand side, in the no-vent configuration without the side vent aperture. This outer wing panel forms the front bodyw...

Front door latch link

Bonnet stay stick Defender

Door Sill Seal - rear, supplied as a left- and right-hand pair. This rubber seal fits along the rear door sill aperture, forming the weather seal b...

Pop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...

Window Regulator for the front door, left-hand side, manual winder type (not electric). This is the mechanism that raises and lowers the front doo...

Front Outer Wing - Left-Hand with the turbocharger aperture in the inner face. This outer wing panel forms the front bodywork over the wheel arch,...