Products

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Rivet, semi-tubular with a semi-round (truss) head, 3/16 in diameter and 3/8 in long. It secures door weatherstrip and seals to the body aperture....

Chain Bracket Series/Lw

Clevis Pin for the tailboard assembly at the rear of the body. It secures the drop-down tailboard's support cable or chain to its anchor bracket, ...

Plain Flat Washer for use beneath bolt heads or nuts where specified. Used across multiple assemblies including alternator mountings, exhaust manif...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Rope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...

Coil Spring Carrier for the 2.0-inch coilover shock assembly. The carrier retains the coil spring on the coilover body, locating the spring between...

Coil Spring Carrier for 2.5in remote reservoir coilover shock absorbers. This component locates and supports the coil spring around the body of th...

Heater Blower Motor supplied without wiring lead (motor body only). This 12V electric motor drives the centrifugal fan within the heater blower un...

Ignition Switch Knob - the rotary knob for the PRS-type combined ignition and lighting selection switch. It fits onto the switch spindle to provid...

Floor Panel Screw x 100

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Rod Guide Bearing Cap Seal (Nok) 2.0

Rod Guide Bearing Cap Seal (Nok) 2.5

Guide Rod 2.5 Coilover (12 19 On)

Guide Rod 2.0 Coilover (08 19 On)

Bush Guide Rod 2.0 Coilover (08 18 On)

Bush Guide Rod 2.5 Coilover (08 18 On)

Dust Seal 2.0 Coilover (05 18 On)

Dust Seal 2.5 Coilover (08 18 On)

Guide Rod Washer for 2.0in remote reservoir coilover shock absorbers. This washer locates on the guide rod of the coilover unit, providing the cor...

Guide Rod Washer for 2.5in remote reservoir coilover shock absorbers. This washer locates on the guide rod of the coilover unit, providing the cor...

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Two-Man Bench Seat Cushion for the rear inward-facing bench seat. This is the fixed rear bench cushion that forms the seating surface of the two-s...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Transfer Box to Gearbox Mounting Stud, 2" length, used to fasten the transfer case to the rear of the main gearbox casing. This stud forms part of...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Door Top Glass Retainer for the front door glazing assembly of Series Land Rovers. This retainer secures the top edge of the fixed front door wind...

Teflon Band 2.0 Coilover (12 17 On)

Teflon Band 2.5 Coilover (12 17 On)

Rear Side Skin - Left Hand Side for the rear body assembly of Series Land Rovers with the 88" wheelbase. This outer body panel forms the lower rea...

Mudshield for the right-hand side of the vehicle. This panel mounts within the inner wing and wheel arch area to deflect road spray, mud and debri...

Hoodstick - a structural bow forming part of the soft-top canvas roof framework on Land Rover vehicles. This hoodstick is a component of the hood ...

Bulkhead Vent Seal - rubber seal for the bulkhead fresh-air vent flap. This rubber seal fits around the bulkhead air vent aperture, sealing the hi...

Door Hinge Bolt

Door Hinge Spring for the rear door hinge assembly. Return spring fitted within the rear end door hinge on station wagon body variants. Provides t...

Locker Door Hinge

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...