Products

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

U-Bolt for the rear leaf-spring suspension of long-wheelbase (LWB) models. The U-shaped bolt passes over the axle and clamps the rear leaf-spring ...

U-Bolt – Rear – 1-Ton clamps the rear leaf spring to the axle. The U-shaped bolt passes over the axle and through the spring seat plate, where its ...

Master Cylinder to Pedal Box Gasket for the hydraulic clutch circuit. This gasket seals the mounting face between the clutch master cylinder body ...

Gearbox Crossmember for the chassis of long wheelbase Series Land Rovers. This steel crossmember spans the chassis rails beneath the gearbox, prov...

Exhaust clamp rubber strap

Exhaust Pipe - RH is the right-hand exhaust downpipe within the exhaust system. It bolts to the exhaust manifold outlet and carries combustion gas...

Exhaust Pipe

Mainshaft Bearing

Lock Washer for the wheel hub nut - a lock tab washer fitted within the hub assembly. It sits beneath the hub nut, with a tab folded against a fla...

Hub Cap for the 101 Forward Control wheel hub. Fits the wheel hub on Series II, IIA, and III 101 Forward Control variants, covering and protecting...

Spacer

Primary Pinion Shim - 2.15 mm for the four-speed V8 gearbox. Used during gearbox assembly or rebuild to set the correct end-float and bearing prel...

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Primary Pinion Shim - 2.00 mm for the four-speed V8 gearbox. Used during gearbox assembly or rebuild to set the correct end-float and bearing prel...

Output Shaft Oil Seal seals the output shaft of the LT95 four-speed gearbox and integral transfer box, retaining gear oil where the shaft passes th...

Bottom cover seal

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Special Bolt

Intermediate Gear Shaft for the transfer gearbox. The shaft carries the intermediate gear that transmits drive from the gearbox mainshaft to the fr...

Needle Roller Bearing

Bearing needle roller

rear output shaft LT95 4-speed gearbox V8 - S3 109" Stage 1 V8 - 101" Forward Control - Range Rover Classic 4-speed V8 - Early 110" 4-speed V8

Heater Tap Adaptor for the heater control circuit. This zinc-plated mild steel adaptor forms the threaded interface between the heater water valve ...

Heater Hose carries engine coolant between the valve and the heater tap, forming part of the heater coolant circuit that feeds the heater matrix. ...

Heater Hose - Series 3 RHD

Heater Hose connects the cylinder head heater outlet into the heater coolant circuit, carrying hot coolant from the engine toward the heater matrix...

Drop Arm for the manual steering box. The drop arm splines onto the steering box rocker shaft and converts the box's rotary output into the fore-an...

Fuel Filler Hose

Shackle Pin for the rear shackle of the front leaf spring. The pin pivots the spring shackle at the rear eye of the front road spring, locating th...

Axle Breather Pipe vents the rear Salisbury axle housing. It connects to the top of the axle casing and equalises internal pressure as the axle oi...

Engine Stud - a threaded manifold stud fitted to the exhaust system of the diesel engine. It threads into the cylinder head to provide a fixed anc...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Handbrake Return Spring is part of the transmission-mounted drum-type handbrake, acting on the relay lever within the parking brake mechanism. Whe...

Breather Hose - Oil Filler to Flame Trap for the engine crankcase ventilation system. This flexible hose connects the oil filler pipe outlet to th...

Banjo Bolt - the hollow union bolt that secures the external oil feed pipe to the cylinder head within the engine lubrication circuit. It clamps t...

Core Plug (cup/expansion plug) seals a casting core hole in the cylinder block, fitted at the rear of the block. It closes the openings left by th...

Blanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...

Oil filler cap

Exhaust Manifold bolts to the exhaust ports on the cylinder head and collects the exhaust gases from the cylinders into a single outlet feeding the...

Exhaust Silencer sits in the rear section of the exhaust system, downstream of the intermediate pipe and ahead of the tailpipe outlet, where it for...

Exhaust Silencer - Stainless sits in the rear section of the exhaust system, downstream of the intermediate pipe and ahead of the tailpipe outlet, ...