for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
O-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...
View full detailsSynchromesh Ring - inner synchroniser ring for the R380 five-speed manual gearbox. Works within the mainshaft synchroniser assembly to bring the g...
View full detailsSwivel Recovery Eye Rotating recovery point that bolts through the recovery-point holes in a winch bumper, providing a secure anchor for a shackle ...
View full detailsSelf Tapping Screw for use in Land Rover body, chassis, and hardware applications.
Thrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...
View full detailsFixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...
View full detailsElectronic Differential Lock (E-Locker) replaces the standard open differential assembly within the axle, providing driver-selectable full differen...
View full detailsDowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...
View full detailsValve Cotter (split collet) for the Rover V8 petrol engine valve train. Locks the valve spring retainer to the valve stem, holding the spring unde...
View full detailsKinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...
View full detailsTow Ball & Pin Hitch Assembly for the towing system, mounting to the rear towing bracket. The assembly combines a tow ball for standard ball-c...
View full detailsAdjustable Panhard Rod - Long - lateral axle locating link within the suspension assembly, supplied in the longer length variant. The Panhard rod ...
View full detailsRear Coil Springs - Medium Load, +2" Lift (Terrafirma), supplied as a pair. This is a LIFT spring: it raises the rear by approximately 2" (50mm) o...
View full detailsCamshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...
View full detailsCam Cover Washer - plain black washer used on the camshaft cover of the Td5 2.5L 5-cylinder turbo diesel engine. It sits under the fixing that ret...
View full detailsMainshaft for the R380 5-speed manual gearbox. The mainshaft is the central driven shaft within the R380 gearbox, carrying the output gear cluster...
View full detailsRear Coil Spring - Heavy Duty, +2" Lift A rear suspension coil spring from the Terrafirma range, seating between the axle and the chassis spring s...
View full detailsWheel Cylinder Brake - RH
Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...
View full detailsPan Head Bolt, M8 x 40mm. Metric pan head bolt for use across Land Rover body, chassis, and interior assemblies.
Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...
View full detailsInjector O-Ring - a sealing ring for the fuel injectors in the electronic fuel injection system. It seals the injector where it locates in its bore...
View full detailsGearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...
View full detailsPlastic Washer - a plastic washer used at the radiator cowl (fan shroud) mounting in the cooling system. It sits under the fixing that secures the...
View full detailsEngine Cover Grommet - a rubber vibration-damping mounting grommet for the acoustic engine cover on the Td5 2.5L 5-cylinder turbo diesel. The grom...
View full detailsWater Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...
View full detailsRadiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back to t...
View full detailsPipe Clamp for the engine oil cooler pipe circuit. This clamp plate secures the oil cooler pipes in the engine bay, restraining them against vibra...
View full detailsTiming Pin (Long) is a workshop special tool used to set the engine timing on the Td5 2.5-litre five-cylinder turbo diesel. The pin locks the cran...
View full detailsCompressor A/C & - TD5 P38 4.6
Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...
View full detailsLow Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...
View full detailsFlanged Nut - M12 for use in Land Rover fastener applications. A metric M12 flanged nut with an integrated washer flange that distributes clamping...
View full detailsThrust Washer 1.45mm Diff - LT230
Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...
View full detailsGasket
Drive Meter Speedo Gear Yellow 22 Teeth
Oil pump relief valve washer V8
Bracket
Upper Radiator Mounting Bracket that locates and secures the top of the radiator in the cooling system. Fitted to four-cylinder TDi and Td5 applic...
View full detailsOil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...
View full detailsHydraulic Lash Adjuster installed within the valve train assembly of Td5 2.5L 5-cylinder turbo diesel engines, positioned between the camshaft and ...
View full detailsEngine Plug - a cylinder head core plug (welch plug) for the Td5 2.5L 5-cylinder turbo diesel engine. Core plugs seal the casting holes left in th...
View full detailsInlet Valve for the TD5 2.5L 5-Cylinder Turbo Diesel engine, as fitted to the Defender and Discovery 2. The inlet valve controls the intake charge...
View full detailsFlywheel Bolt for the 2.5L Td5 five-cylinder diesel engine with manual gearbox. This bolt secures the flywheel to the rear flange of the crankshaft...
View full detailsCam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...
View full detailsPower Steering & ACE Pump Pulley mounts to the hydraulic pump drive shaft and is turned by the engine's auxiliary drive belt. Drives the power...
View full detailsStepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →