Land Rover Discovery 2 Parts

Transfer Box - LT230 43D is a reconditioned two-speed transfer gearbox with a 1.4:1 high-range ratio. The transfer box mounts to the rear of the m...

Synchroniser Assembly for 3rd and 4th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The assembly locks the selected gear t...

Oil pump relief valve washer V8

Synchroniser Assembly for 5th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The sliding sleeve is moved by the fifth-gear ...

Transfer Box Overhaul Kit for the LT230 transfer box. The LT230 is the two-speed transfer box that splits drive from the gearbox between the front...

Wheel Arch Trim Kit providing a full six-piece set of extended wheel arch flares that fit over the standard arches. The flares extend approximatel...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Door Check Arm Pin for the door check strap assembly. This pin secures the door check arm to its mounting bracket on the body, retaining the arm t...

Wiper Motor Grommet for the rear screen wiper assembly. It seals the aperture in the rear door or tailgate where the wiper motor spindle passes thr...

Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...

Stud

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Weatherstrip - sealing strip for the rear tailgate end door glass assembly. This weatherstrip forms the perimeter seal between the rear window gla...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Land Rover Oval Name Badge - Plastic - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground, moulded in ...

Pin - Split

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Stepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Clutch Plate

Bow Shackle Bow-shaped recovery shackle with a threaded pin, used to connect a recovery strap or rope to a recovery point on a winch bumper. The w...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

High Note Horn - the higher-pitched element of the dual-tone warning horn assembly. Mounted behind the front grille or valance and paired with a l...

Exhaust Manifold Gasket for the 4.0L and 4.6L EFi V8 petrol engine. This twin-port gasket seals the exhaust manifold-to-cylinder head joint at two...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Rock Sliders

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

LED Number Plate Lamp - rear licence plate lamp using LED illumination. Mounted above the rear number plate, the lamp illuminates the plate for ni...

Adjuster