Land Rover Discovery 2 Parts

Parts coverage

The Discovery 2 (L318) is a body-on-frame ladder-chassis vehicle built from 1998 to 2004 at Solihull. It runs live axles front and rear with permanent four-wheel drive, and was available with the 2.5-litre Td5 inline-five diesel or the 4.0-litre and 4.6-litre Rover V8 petrol engines. Gearbox options were a five-speed manual and a four-speed automatic. Some later variants were fitted with ACE (Active Cornering Enhancement), an electronically controlled hydraulic anti-roll system.

Budget Parts stocks parts across the full range of Discovery 2 service and repair requirements. Coverage includes:

• Suspension and steering: air springs, shock absorbers, control arms, steering joints, and related hardware
• Engine: gaskets, seals, filters, injector seals, coolant components, and ancillaries for Td5 and V8 variants
• Fuel system: in-tank pumps, fuel pressure regulators, sealing washers, and connectors
• Drivetrain and transmission: propshaft bolts, output shaft seals, transfer box seals, clutch components, and gearbox service items
• Braking: discs, pads, caliper hardware, and hydraulic components
• Cooling and heating: thermostats, thermostat housings, water pumps, hoses, and coolant connectors
• Body and chassis: crossmember repair sections, chassis hardware, body fasteners, and trim fixings
• Electrical and lighting: bulbs, sensors, connectors, and harness fixings

Genuine and direct OEM supply for the Discovery 2 is more limited than for later Discovery generations, as production ended in 2004. Budget Parts maintains aftermarket and compatible OEM stock for this generation, including parts that have been discontinued from the Land Rover Genuine supply chain.

Reference note: The JLR Classic parts portal at parts.jaguarlandroverclassic.com lists the Discovery 2 under the L318 designation with a production range of 1998 to 2004 and covers the same parts categories listed above.

Platform and fitment guidance

The Discovery 2 does not share a platform with the Discovery 3 or Discovery 4. It is the last Land Rover SUV to use the ladder-frame architecture derived from the original 1970 Range Rover underpinnings. When the Discovery 3 (L319) arrived in 2004 it moved to an entirely different Integrated Body Frame architecture with independent air suspension, meaning no structural, suspension, or driveline parts cross over between the two generations.

The Discovery 2 does share some non-structural hardware with the Defender where both were fitted with the same Td5 engine from 1998 onwards. Td5-specific engine components such as injector seals, dipstick O-rings, and manifold studs may be common across the two platforms, but always confirm fitment by part number before ordering.

ACE-equipped Discovery 2 vehicles use hydraulic actuators connected to the front and rear anti-roll bars. If your vehicle has ACE fitted, confirm this before ordering suspension components, as certain anti-roll bar and bush specifications differ from non-ACE variants.

For vehicles built before and after the 2002 model year update, some sensor, injection system, and electrical connector specifications changed. Confirm your production year from your VIN before ordering electrical and fuel system parts.

VIN and production run guidance

The Land Rover Discovery 2 was produced from 1998 to 2004 in a single generation with a mid-cycle update for the 2002 model year. Ordering by year and engine variant gives the best fitment match for the majority of parts. For electrical components, sensors, and fuel system items, confirming your exact production date via VIN is strongly recommended.

Your VIN is a 17-character code on the A-pillar door jamb, on the windscreen base, or in your vehicle documentation. The 10th character identifies the model year. Land Rover publishes a VIN model year guide at landrover.co.uk that maps the 10th character to the corresponding production year.

If you are ordering suspension, engine, or fuel system parts and are unsure of your production date, use the VIN reference before placing your order. Product listings on this site confirm fitment by model and year. Where a part fits a specific production range only, this is noted in the listing.

Technical guides for Discovery 2 owners

The guides below cover diagnostic and maintenance topics directly relevant to the Discovery 2 (L318). They provide technical depth on common failure patterns and correct replacement decisions. These guides support the parts range on this page and are intended to be read before placing an order where a fault has been identified.

Related component collections

If you know the type of part you need, these category collections cover the relevant components across all compatible Land Rover models: