Land Rover Discovery 2 Parts

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Seat Belt Bolt Cap is a trim cover that fits over the head of a seat belt anchor bolt. It conceals the mounting bolt at a seat belt anchorage poin...

Rally 1000 Long Range Driving Light

Front Mudflap Set mounting behind the front wheels to deflect road spray, mud and stone debris away from the lower body, sills and following traffi...

13-Pin Tow Socket for the trailer electrical connection, mounting at the rear of the vehicle within the towing wiring circuit. The 13-pin format c...

KIT - STRIPE DECAL STC50061

Touch-Up Paint Stick in Zambesi Silver. The stick applies a small quantity of colour-matched paint to stone chips and minor scratches, restoring t...

Touch-Up Paint Pencil in Bonatti Grey Metallic (paint code 19K512). The pencil applies a small quantity of colour-matched paint to stone chips and...

Heater Blower Speed Resistor sets the lower fan speeds of the heater and ventilation blower in air-conditioned applications. Wired in series with ...

Locking Nut - a self-locking nut used at the anti-roll bar fixings. It secures the anti-roll bar mounting within the suspension, and its locking f...

Touch-Up Paint Pencil applies the Epsom Green body colour to small stone chips and scratches in the paintwork. The pencil applicator gives accurat...

Drive Plate Screw is a threaded fastener used in the V8 automatic transmission drive assembly. It retains the drive plate (flexplate) to the crank...

Cylinder Block Screw is a threaded fastener used on the V8 EFI petrol cylinder block assembly. It secures ancillary components and mounting bracke...

ABS Modulator for the four-wheel anti-lock braking system, forming the hydraulic control unit of the ABS circuit. The modulator sits between the m...

High/Low Gear Retaining Nut for the LT230 transfer box. This nut secures the high/low range gear on the transfer box mainshaft, holding it against...

Power Steering & ACE Reservoir holds the shared hydraulic fluid supply for the power-assisted steering and Active Cornering Enhancement (ACE) c...

ACE Pipe - Pump To Valve Block - Front - V8 is a high-pressure hydraulic line within the Active Cornering Enhancement (ACE) system. It carries pre...

Plain Washer, an M6 flat washer. It fits under the head of an M6 bolt or nut to spread the clamping load over a wider bearing area and protect the...

Stud - Cylinder Head & Front Cover - Td5 2.5L five-cylinder turbo diesel. Fixing stud used at the cylinder head and front cover joint, at the ...

Side footstep mounted along the sill, providing a step for entry and exit and for reaching the roof line.

Drive Belt for the power steering pump drive on the V8 petrol engine, in the configuration with ACE and without air conditioning. This belt is dri...

Cylinder Block Plug - sealing plug fitted to the cylinder block casting. The plug closes a machined port in the block, sealing the casting so that...

Bolt is a hexagonal-head screw with a 5/16" UNC thread, 1/2" long. It is used as a general fixing across several assemblies: the air temperature c...

Escutcheon - finishing surround for the rear end door lock barrel, part of the rear door lock and casing assembly. It fits over the lock cylinder ...

Facia Mat - the moulded rubber mat that lines the recessed tray on the top-centre of the facia (dashboard). It gives a non-slip surface for small ...

Bezel Trim is the trim surround that frames the front fog lamp where it sits in the front bumper. It locates into the left-hand side of the front ...

Headlamp Levelling Switch is a rotary switch mounted in the facia switchgear. It sets the headlamp beam height to compensate for vehicle load, com...

Blanking Panel is the binnacle switch blank for the instrument binnacle switch panel. The blank fills an unused switch position in the binnacle, p...

Monobolt Rivet - 1/4" structural blind rivet for body and chassis fastening. The Monobolt is a high-strength blind rivet set from one side of the ...

Washer A washer used in bolted and screwed fixings to spread the clamping load over the joint face and to protect the surface as the fastener is ti...

Body Mount Washer is a load-spreading washer used at the body-to-chassis mountings. It sits under the body mount fixing to distribute the clamp lo...

Retainer Ring for the R380 5-speed manual gearbox mainshaft. It locates and retains the mainshaft 5th and reverse gear assembly, holding the gear ...

EGR Valve Filter is a service component of the exhaust gas recirculation (EGR) system, fitted in line with the EGR solenoid control valve. It filt...

Clip — a 6 mm Starlock push-on retaining washer used as a general-purpose fastener across several systems, including exhaust mounting, trim and oth...

Air Cleaner Mounting Rubber for the engine air intake system. This flexible rubber mount locates and supports the air cleaner (air filter) housing...

Ancillary Belt Drive Guard is the protective cover fitted over the auxiliary belt drive at the front of the V8 engine. It shields the drive belt an...

Banjo Bolt for the brake flexible hose connection in the hydraulic braking circuit. This hollow bolt secures the banjo end of a brake flexible hos...