Genuine Land Rover Parts

Bulb Holder - Sidelamp is the bulb holder for the sidelamp (front parking lamp) within the exterior lighting system. It retains the sidelamp bulb ...

Brake Pad Set for the rear axle disc brake assembly. The pads locate within the rear calipers and clamp against the rear discs, generating the fric...

Brake Pad Set for the front axle disc brake assembly, for use with vented front discs. The pads locate within the front calipers and clamp against ...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Kit - Mudflap - Rear

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Hexagonal Screw - sump pan retaining screw for the ZF four-speed automatic transmission. The screw passes through one of the pressed retaining pla...

Corner Fixing Plate - pressed retaining plate for the automatic transmission sump pan, corner position. The sump pan on the ZF four-speed automati...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Coolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...

Bracket - Support

Hose - Radiator

Intermediate Exhaust Heat Shield - heat shield for the intermediate section of the exhaust system. It mounts between the exhaust pipework and the ...

Coolant Expansion Tank Cap - pressure cap for the cooling system expansion tank, rated at 15 psi. The cap seals the expansion tank and regulates s...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Bush - Stabilizer Bar Link

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Snap-sac trim clip - the push-in plastic fastener that secures interior trim panels to their supporting structure. The clip passes through a hole ...

Rear Door Lock Assembly - LH - complete latch and lock mechanism for the left-hand rear door, operating within the door locks and handles assembly ...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Relay - Direction Indicator Flasher is the electronic flasher unit that sets the pulse rate of the direction indicator and hazard warning circuits....

Relay is a 12V 40 A normally open (make-contact) relay used across the body and engine electrical circuits. Energising the control coil closes the...

Transfer Box Switch Wire Adaptor for the LT230 transfer gearbox. This short harness link connects the main vehicle wiring loom to the switch on th...

Speed Sensor for the transfer gearbox speedometer drive. This 2-pin inductive sensor reads a toothed reluctor on the transfer box output, generatin...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Moulding - Bumper Protection

Brake Light Switch mounted at the brake pedal. Operated by the brake pedal, this switch signals the stop lamps to illuminate when the brakes are a...

Breather Hose for the 300 TDi crankcase ventilation system. The hose carries crankcase breather (blow-by) gases from the engine breather outlet ba...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...