for Discounts / VAT
for Discounts & Correct VAT
Land Rover brake parts for Defender, Discovery, Range Rover, Freelander, and Series 2/3 vehicles. Discs, pads, calipers, Electronic Parking Brake components, ABS sensors, and brake fluid in one collection. ECE R90 compliant friction parts. Stocked in the Netherlands for EU dispatch with no customs charges.
CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...
View full detailsBrake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...
View full detailsBrake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...
View full detailsDust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...
View full detailsCaliper Bolt for the front brake caliper assembly. This bolt secures the brake caliper to the hub carrier. It is a critical fastener in the front ...
View full detailsBrake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...
View full detailsVacuum Pump Seal - 2.7 TDV6 is the sealing component for the engine-driven vacuum pump on the 2.7L TDV6 diesel. The vacuum pump is mounted on the ...
View full detailsBrake Drum Clip is a retaining clip within the rear drum-in-hat parking brake (handbrake) assembly. It secures the handbrake shoe against the back...
View full detailsRear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...
View full detailsBleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...
View full detailsBrake Disc Bolt - M10 x 20mm securing the brake disc to the hub flange. M10 x 20mm bolt with 1.5mm thread pitch. Multiple bolts are required per d...
View full detailsBrake Disc - a rear vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw a...
View full detailsParking Brake Actuator Repair Gears - replacement drive gears for the electric parking brake (EPB) actuator module. Replaces the internal gears th...
View full detailsParking Brake Actuator Repair Kit - the internal service parts for the electric parking brake (EPB) actuator module. Replaces the worn drive gears...
View full detailsBrake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...
View full detailsBrake Booster Repair Kit covering the vacuum servo unit that sits between the brake pedal pushrod and the master cylinder in the hydraulic braking ...
View full detailsTriple Brake Pipe Clip from the brake pipe routing hardware. It retains three rigid brake pipes side by side in one mounting, holding them at a fix...
View full detailsRear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...
View full detailsSensor - ABS
Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...
View full detailsBrake Spring Kit - Parking Brake for the rear drum-in-disc parking brake assembly. This kit supplies the return spring hardware for the parking br...
View full detailsBrake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...
View full detailsBrake Caliper Piston for the rear hydraulic disc brake assembly. The piston sits within the caliper bore and transfers hydraulic pressure from the...
View full detailsRear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...
View full detailsBrake Pad Set is a set of front disc brake friction pads for the front-axle braking assembly. The pads locate in the front brake calipers and are ...
View full detailsKit caliper repair
Brake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...
View full detailsBrake Calliper Fitting Kit for the rear brake callipers. This kit contains the slider pins and rubber dust boots for the rear brake calliper. The ...
View full detailsBrake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...
View full detailsBrake Pad Set is a set of front disc brake friction pads for the front-axle braking assembly. The pads locate in the front brake calipers and are ...
View full detailsFront Brake Caliper Pin Kit covering both front calipers (left and right). The kit supplies the guide pin hardware required when servicing the fro...
View full detailsBrake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...
View full detailsBrake Caliper Screw for the front brake caliper and parking brake installation. Retains the caliper or its carrier to the mounting face on the hub...
View full detailsBrake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly. The carrier bolts to the rear hub carrier and holds t...
View full detailsBrake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly. The carrier bolts to the rear hub carrier and holds t...
View full detailsBrake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly, dimensioned for the rear disc size used with the 18-in...
View full detailsBrake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly, dimensioned for the rear disc size used with the 18-in...
View full detailsABS Wheel Speed Sensor is part of the anti-lock braking system. Mounted at the wheel hub, it generates a signal proportional to wheel rotation and...
View full detailsGrommet for the inspection aperture in the rear brake backplate. The backplate carries an access hole through which the parking brake shoe adjuster...
View full detailsGrommet for the inspection aperture in the rear brake backplate. The backplate carries an access hole through which the parking brake shoe adjuster...
View full detailsBrake Pedal Pad for automatic transmission applications - the moulded rubber cover that fits over the brake pedal lever in the pedal box assembly. ...
View full detailsHandbrake Shoe Fitting Kit
Sensor - ABS - Vented
Front Brake Caliper Carrier - the machined mounting adaptor between the front hub carrier and the brake caliper. The carrier bolts to the suspensi...
View full detailsHandbrake Shoe Spring Repair Kit - the springs for servicing the rear parking-brake shoe assembly, the drum-in-hat parking brake integrated into th...
View full detailsParking Brake Cable Bracket from the parking brake cable routing. The bracket anchors the cable outer casing at a fixed point on the vehicle, so th...
View full detailsBrake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...
View full detailsBrake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...
View full detailsPlatform Load and Wear Patterns
Brake-component wear on a Land Rover or Range Rover follows the platform. Discovery 3, Discovery 4, and Range Rover Sport L320 share the IBF chassis architecture and similar braked-mass figures, with Discovery 3 kerb weight running from 2,394 to 2,536 kg across variants. That mass loads pads and discs predictably under repeated use, and pad compound choice matters more than it does on a lighter vehicle.
Range Rover L405 and Range Rover Sport L494 share the D7u aluminium platform and continue the heavy-platform pattern. Defender Classic and the new Defender L663 sit on different architectures but share the same off-road exposure factor: mud, water, and grit accelerate caliper piston binding and pad wear in ways that road-only platforms don't see. Freelander 1 and Freelander 2 are lighter and front-biased; the most common brake-side service item is handbrake cable replacement on both generations.
Series 2 and Series 3 use mechanically simpler hydraulic brake systems with no electronic actuation, but correct component pairing (disc, pad, caliper seal kit) still determines whether the brake job lasts.
Collection ScopeThe Land Rover Brake Parts collection holds:
For brand-specific filtering, Ferodo brake parts and TRW brake parts are listed under their own collections within this category.
Pre-Purchase Fitment ChecksBrake parts are usually replaced as a matched system, not as individual components. A buyer ordering pads alone for a Discovery 4 or Range Rover L405 typically generates a comeback within a service interval. Check the following before placing an order:
The EPB on Discovery 3, Discovery 4, Range Rover Sport L320, and L405 cannot be retracted manually for pad replacement. The system must be placed into service mode using a diagnostic tool (Land Rover diagnostic tools). Ordering rear pads without service-mode access usually means a delayed fit, not a quick replacement.
These are buyer-side patterns that generate avoidable comebacks. None of them are diagnosis or repair procedures. They are part-selection patterns.
Brake replacement on Land Rover models often touches adjacent systems that wear on similar cycles.
Brake pads, brake discs, and brake drums sold as aftermarket replacement parts for vehicles type-approved after the relevant cut-off date must hold ECE Regulation 90 approval. The regulation requires replacement pads to perform within a 15% tolerance of original equipment friction characteristics, and applies to brake discs for passenger cars registered after November 2016 and to brake pads since 1 January 1999. ECE R90 approval is the baseline for EU road use, not a premium tier.
EU Stock and DispatchBrake parts in this collection are held in the Dutch warehouse network for EU dispatch. EU buyers pay no customs charges or VAT surprises on inbound delivery. Trade and workshop buyers can access the wholesale portal for trade pricing and dedicated account support.
Technical GuidesDiscovery 3, Discovery 4, and Range Rover Sport L320 EPB failure is usually traced to worn rear brake shoes or stretched handbrake cables, not the actuator motor itself. The diagnostic and repair path covered in this guide explains what fails first and which parts are commonly needed.
Discovery EPB fault diagnosisThe L320 air suspension and brake systems share heavy-platform wear patterns, particularly on vehicles used for towing or heavy load. This guide covers the compressor, air spring, and suspension component failures most often seen alongside or shortly before a major brake service.
Range Rover Sport L320 air suspension guideYes, provided they hold ECE Regulation 90 approval. ECE R90 has been mandatory for replacement brake pads on EU-registered passenger vehicles since 1 January 1999, and for replacement brake discs since November 2016. R90-approved aftermarket pads must perform within 15% of the original equipment's friction characteristics. Both Ferodo and TRW brake parts in this collection carry R90 approval on relevant part numbers.
Yes. The Electronic Parking Brake must be placed into service mode using a diagnostic tool before the rear caliper piston can be retracted. Attempting to retract the caliper without service mode can damage the EPB actuator. Workshop access or a compatible diagnostic tool is a prerequisite, not optional, for rear brake replacement on these platforms.
OEM-grade pads target the original friction characteristics of the vehicle: predictable bite, consistent fade resistance, and acceptable pad life under normal road use. Performance pads typically use a higher-temperature friction compound and are intended for towing, sustained heavy load, or off-road use on Defender, Discovery, and Range Rover platforms. Performance pads can be noisier and may wear faster under normal driving. Match the pad to how the vehicle is actually used.
We recommend checking the model year and engine variant before ordering. Brake-component sizing varies by generation (Discovery 3 versus Discovery 4 versus Discovery 5), by engine option (heavier engines often run larger discs), and by trim level on Range Rover variants. The VIN or chassis plate is the most reliable identifier for fitment lookup. The chassis plate sits on the A-post or near the bulkhead, depending on market variant (LHD versus RHD).
Yes. Series 2 and Series 3 brake components, including drum brake parts and the hydraulic-only system items, are listed within the brake-parts collection. Series vehicles use mechanically simpler systems with no electronic actuation, but correct disc, pad, and caliper-seal pairing still determines how long the brake job holds.
Updated: 17 May 2026