Land Rover Defender Parts

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Rear Propshaft for the short-wheelbase chassis, forming part of the driveline between the transfer gearbox and the rear axle. The propshaft transm...

Sealing Washer for the carburettor choke switch on petrol engine applications. Fitted at the choke switch, it seals the joint at the fitting to pr...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Glow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

Differential Washer is a plain washer used within the front and rear differential assembly. It seats beneath a threaded fastener to distribute cla...

Radius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...

Oil Pressure Sensor Monitors engine oil pressure in the lubrication circuit and signals the oil pressure gauge or warning lamp on the instrument pa...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

O-ring

Steering box sector shaft seal kit for the steering system. This kit contains the sealing components required for the sector shaft assembly withi...

Inlet & Exhaust Manifold Gasket - 300TDi

Window Channel

Polyurethane Boot - Defender - Discovery 1/2 - RRC - P38

Exhaust Manifold to Turbo Gasket seals the joint between the exhaust manifold outlet and the turbocharger inlet within the exhaust manifold and tur...

Radius Arm Bush - Front for the front suspension radius arm assembly. This rubber bush is pressed into the forward end of the front radius arm and...

Master Lighting Switch mounted on the steering column, providing the primary control for the side lights and headlamps. It forms part of the steer...

Rear Shock Absorber - hydraulic telescopic damper for the rear suspension. Mounted between the rear axle and the chassis, it damps the oscillation...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Gasket kit 300tdi lower block set no rear crankshaft seal

Stud is an M10 threaded stud, 35 mm long, used as a mounting fastener at several engine locations - the cylinder head, manifold, power steering pum...

Rear shock absorber

Brake caliper 110/130 LH rear

Brake Caliper - Rear - RH

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Ignition Condenser for the contact-breaker distributor, of the Lucas type, supplied with a long lead (17-7/8 in). Wired across the contact-breaker...

Shock Absorber for the front suspension, a heavy-duty oil-filled hydraulic damper. Mounted between the axle and the chassis, it damps the oscillat...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Coolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...

Idler Tensioner Pulley for the auxiliary (serpentine) drive belt system. Mounted on the automatic belt tensioner arm, the pulley bears against the ...

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Coolant Hose - Radiator Upper is the upper hose in the engine cooling circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries hot coolant from...

Engine mounting

Radiator Rubber Mount for the engine cooling system. This rubber mounting locates the radiator in its support panel and cushions it against engine ...

Snap sac

Hinge Packer Shim for the door hinge assembly. Fitted between the hinge and its mounting face to set door alignment. Adding or removing shims adju...

Steering Damper Assembly for the front axle steering linkage. The hydraulic damper mounts across the steering linkage, where it controls lateral o...

Blanking Plug Grommet for the dash assembly. This rubber plug fills an unused aperture in the dash panel - such as the opening for the hand throttl...

Crankshaft Oil Seal - Rear - Heavy Duty for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal hou...

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Headlamp Bezel - stainless steel, 7". The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing ...

This steering drop arm transmits movement from the steering box output shaft to the steering linkage, enabling directional control at the front axl...

Rear Body Crossmember is a structural member spanning the rear of the body, carrying the rear of the load area and tying it into the chassis mounti...

Rocker Shaft Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the rocker shaft assembly to the cylinder head. It clamps the rocker s...