Land Rover Defender Parts

Brake Disc for the rear axle. This disc is the rotor that the rear caliper clamps to slow the wheel. Sized for the 20-inch brake disc and caliper ...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Connection - Water Outlet

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Oil Filter Element and Seal

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Oil Tube Gasket seals the turbocharger oil drain (return) pipe where it joins the engine, within the turbocharger lubrication circuit. After lubri...

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Wheel Spacer Set mounts between the wheel hub and the road wheel to increase track width, fitting over the hub and carrying a fresh set of studs fo...

Brake Disc for the rear axle. This disc is the rotor that the rear caliper clamps to slow the wheel. Sized for the 20-inch brake disc and caliper ...

Bolt

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Valve Stem Seal seals the point where the valve stem passes through the cylinder head valve guide, controlling the oil reaching the stem and preven...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Lazer ST4 Evolution LED Spotlight - a compact four-LED auxiliary driving lamp producing a controlled long-range beam for forward illumination. The...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on modern vehicles equipped ...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on selected vehicles utilizi...

Front Suspension Arm Bush - Inner Mount - the rubber-bonded pivot bush at the inner mounting point of the front suspension arm, within the front su...

Wheel Bearing - Rear, a component of the rear hub assembly. The rear wheel bearing carries the vehicle's rear load and allows the road wheel and h...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Idler Pulley for the accessory drive belt system of the 2.0L I4 Ingenium (AJ200 / AJ20) petrol and diesel engine. The idler pulley guides the rout...

Plug cooling system bleed

Front Suspension Arm Bush - the rubber-bonded pivot bush that mounts the front suspension arm to the subframe, within the front suspension arm asse...

Front Strut Boot Kit renews the protective gaiter and mounting hardware for a front air suspension strut, part of the four-corner air suspension sy...

Timing Chain Kit for the valve timing drive of the Ingenium 2.0L 4-cylinder diesel engine (AJ200 series). The timing chain drive synchronises cran...

Air Suspension Compressor - AMK-type compressor assembly from the air suspension supply circuit, for vehicles with four-corner air suspension. The...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Front Brake Disc, 363mm diameter, ventilated construction, supplied singly. The disc runs within the front caliper and provides both the friction ...

Brake Pad Set - Rear - friction pad set for the rear brake discs and calipers assembly, supplied as a complete axle set covering both rear wheels. ...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Coolant Outlet Pipe - Upper - SC

Pump - Water Hepu

Valve - Control

Bolt - a structural fastener used at chassis and front suspension mounting points, including the front cross member and stabiliser bar crossmember,...

M16 Nut for the front suspension arm. Secures a front suspension arm mounting fastener, holding the joint under suspension loads.

Nut - Flag Type

Bolt

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...